Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Using S132 v4.0.2, is it possible to disable DLE (i.e. make it NOT set the LE Data Packet Length Extension used bit in the LL_FEATURE_RSP)?
Alternatively, is there a way...
experimental_ble_app_multiperipheral_pca10040_s132 connectivity issue.zip
I’m getting an LMP Response Timeout disconnect reason about 50% of the time when trying to get...
Hi guys
I have been working with a nordic ble device (NRF51822) configured as a Beacon. I am implementing an IOS app, using Apple framework " CoreLocation". My goal is...
I'm looking at using an nRF51822 in a Gazell or ESB application. I prefer not to have any softdevice loaded at all.
What is the correct procedure to perform clock calibration...
Hi
So far I have been using the examples from Keil 5 pack installer.
Now I tried loading some from the SDK example folder and I have issues with includes.
What do I need...
I included button less DFU service in the proximity profile example.When i compile i am getting the following error.
..\..\..\..\..\..\components\libraries\bootloader\dfu...
Hello,
I am working with the example "experimental ble app cgms" in SDK 13.0 and using nRF52832 DK.
when a connection was settup and pairing completed, the CGMS sensor...
I want to ask general question about antenna designing as I am designing antenna to be used with NRF52.
The picture attached with this message shows a printed antenna coil...
At the moment I'm sending a notificaties during the BLE_GAP_EVT_CONNECTED event. This sometimes results in various errors but I can take care of those. The issue I'm having...
GerberVINR-178.zip
SchematicVINR-178.pdf
Bottom layer
Top Layer
IC on the PCB is marked as follows: nrf51822 QFAAHO 1627WM.
I am able to program the custom...
Hello,
I want to create BLE connection between two different modules - nrf51822 and TI CC2564 (possibly Laird BT800). Is there any chance on using Gazell protocol on other...
Hi,
if I got it right, the Radio Timeslot API is not supported by the S140 softdevice. Is this right? Why is this and are there any plans to support the API in later versions...
HI, every one, I joined the watchdog program in application,i use sdk11.0, and i found the problem that when i download the program , the MDK compiler point out "error: flash...
Hi,
I am doing development on Android platform. I am using Marshmallow device to develop my BLE application. Many times I am getting status code 129 in onServicesDiscovered...
