Hi,
I'm using the nRF52833 to develop a BLE beacon and built a Bluetooth gateway for my application.
Application Requirements:
The beacon should advertise using...
Hello,
I want to perform some antenna measurements and compare the rf performance of my custom PCB with an nrf9160 SiP with the nrf9160 dk.
To perform some antenna measurements...
Hi I want to build a multi role BLE device.
As a peripheral it shall stream ADC data with arounf 20 kbytes per second.
As Central it shall receive adv_nonconn_ind packets...
Dear Nordic Engineers
I developed a PWM function to drive the RGB LED. Then I found a problem, which is w hen I used a PWM signal of one channel to control the RED light...
I get error provisioning key on nRF54L15 and NCS 3.0.1. I tried using "Erase all" in nRF connect SDK Programmer, but it doesn't help. Please check also the attached log. nrf54l15dk...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi
I have a code previously can be built in NCS 2.91:
However, when I use the new NCS 3.01, it can not be built, the error is:
Could you please help me figure out...
Hi;
Is it necessary to reset SoftDevice when using NVIC_SystemReset ()?
The SoftDevice must only be initialized if a chip reset has occured.
I saw the above comments...
Here is the code I'm using to test it out:
static float number = 0.5678905;
NRF_LOG_INFO("Float number: "NRF_LOG_FLOAT_MARKER"\n\r", NRF_LOG_FLOAT(number));
And...
Hello,
I am working on NRF52382 custom board, where I am running a timer of 30 sec to get a value every 30 sec.
I want to save this value in flash.I am well aware of...
Does the s210 softdevice not function on the nRF51822? I see it available for the nRF51422 here but it is listed under the 51422 only.
I have a v1.1.0 PCA10031 (nrf51422...
Hello,
I developed an application for the nrf51822 Smart Beacon, SDK11 s130, that basically advertises the battery lvl of the beacon, the staus of button_1 and the number...
I have a nRF 52 DK board. I have flashed dtm example onto it. I have connected a USB to serial UART interfacing board ( www.sparkfun.com/.../12731) to the respective Tx, Rx...
Both the capacitive touch library and the driver (which is better ?) are using the analog inputs.
There are only 8 of them , and we need 10 at least buttons.
Is there...
I'm migrating from SDK11 to SDK13. My custom service is based off Heart Rate Service, so I started from the new SDK13 example of HRS, and updated all the initialization code...
Hi,
on Android, I sometimes get delayed notifications. I measure realtime data and send them over notification, and I can see data change on Android with approx 1 s delay...
Could Nordic please confirm that the "SB13-SB15" and "SB23-SB25" silkscreen markings incorrectly imply that pin 1 of the SPI flash part, which is actually "!CS" would appear...
I have a custom PCB with an nrf51422 powered by a coin cell battery. The EE who designed the board assured me that the battery voltage could be measured internally through...
Hi community
In order to discovery the server, I have read some examples and I got some questions regarding the use of the following methods:
sd_ble_gattc_primary_services_discover...
Hi,
Is it possible to add additional antenna on the beacon ( NRF51) in order to increase the range ?
If yes kindly let me know the list of available or recommended antenna...
