There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi,
i am working on RTC to create custom clock to measure time it is working fine but when i initialise ble stack and softdevice and adverticeinit it is not working. and...
Hi,
Maybe someone can point me into the right direction, I'm on S110 and SDK10 for hardware/legacy reason.
I have a pstorage function using init, load, clear and write...
Hi.
I am investigating the cap touch for a while, and I am working directly with the capacitive driver from here.
As being said there and other places, the driver will...
Hi all
What is the minimum required length of a LOW pulse to be detected by the nRF52832 via GPIO SENSE mechanism? I couldn't find it in the product specification.
I...
Hi Nordic Team,
I am using board PCA10040 wtih nRF52832 SDK 11.
I have Added DFU code to ble_app_hrs_freertos example.
Once I will go for DFU from nrf Mobile Application...
Hi all
I was investigating a NMI_interrupt today and found out that it was caused by a race condition in the fstorage module.
The problem may occur after a flash operation...
HI ,
I am using nrf52832 with s132 . I am trying to measure ADC value at some periodic interval. In nrf_drv_timer_init() function , code gets restarting after executing nrf_timer_event_clear...
Hi,
I use bootloader from SDK6 and I have sd_power_system_off() in on_ble_evt in event BLE_GAP_EVT_TIMEOUT and BLE_GAP_EVT_DISCONNECTED. I use SDK7.1 and SD110 7.1.
It cause...
I'm programming an application that uses the NUS, and I'm trying to test my code using the Android version of nRF Connect. I'm using a nRF52832 on dev board PCA10040, and...
Hello,
With sdk13 and app_pwm library, I only got 9bits resolution for 32KHz freq.
The pwm should have 16bits resolution, with max freq 100KHz?
please could anyone...
hi ,all
I feel confused about" out_of_sync" and" in_sync" parameters .If a devece is in sync,how the channels was changed ?And what's the use of"nrf_gzll_set_device_channel_selection_policy...
we builded " BLE to IR " using nRF51822 , it was working fine with out the softdevice.
problem start when we integrated with the SoftDevice .
1.the problem that we need...
Hi.
I am trying to get a capacitive sensor library using a button ( 2 plates, one to ground, one to the AIN, separated).
It's going crazy, sometimes it just get tones...
hi,
I'm designing a board with nrf51822 chip. this board work on 2450 lithium rechargeable battery and it contain an MCP73831T circuit which is responsible of recharging...
