I'm trying to design a very low power sensor that takes readings using ADC and SPI 200 times a second. I'm a bit worried by the current EasyDMA uses (1.1mA). As far as I can...
Hi, I am working on a project where I want to make one nrf51288 chip as central hub and connect that to a android phone and other salve nrf51288 .
idea similar to this: ...
Hi,
I have a code programming the nRF51422 development board to write to a Sharp Memory 96x96 pixel LCD screen using SPI.
Currently the code writes two numbers and a...
I've modified the ble_app_uart example by adding GPIOTE so that the transmitter sends a character to the receiver when a GPIO pin is toggled. This part is working well.
...
Hi,
I am working on my hardware product having nRF-51422 chipset. I just came to know from forum post that
nRF-52 chips will get arduino IDE support as standalone. I want...
Hi!
I've been using PCA10028 for a long time and I had some bricking issues but I've managed to un-brick it with "nrfjprog --recover" and everything would work again. ...
I want to build nrftoolbox app in android studio. I downloaded the zip file from the github website and also the required dfu library. I unzipped both the files in a folder...
Hello,
I am working on a custom PCB with a nRF52832 and I've been unable to get the ON IDLE power under 480uA. Here are the basics regarding the setup
nRF52832 Rev...
Hello! I'd like to know if S132 v3 implements the frequency hopping scheme defined by BLE.
I've read some documentation on Gazell, but from what I understood, that is a...
Whenever our battery runs to zero, or if we have a reset due to voltage droop, the unit will not auto-connect and the user is forced to "forget" the device in iOS bluetooth...
Hello,
i'm trying to use nRF UART driver (nrf_drv_uart) to implement a high level UART manager.
I followed indications on SDK documentation but it doesn't work and i think...
Working on a project to set up a bidirectional UART to SPI link over ESB with nRF52832 (PCA10040), using SDK 13.0.
Working from provided examples for PTX and PRX, I manage...
Hello,
I've implemented one custom service very similar with NUS. I have two peripherical devices that are running in two PCA10040 with S132 12.1, and one central device...
I have set up some code using the ESB example in SDK v12.2.0 I and am able to transmit and receive packets between two nrf51 dongles, with no issues. However, when I program...
Hi,
I did time measurements for packet transmission (notification) and saw only ~ 30 microseconds (about 1000 ticks with 0 prescale) difference between sending one or up...
Hi,
I am using nrf51822 chip. I am using RTC to generate irq with CC. Everything works fine for IOS and old Android version. New android version makes 2 things when I disconnect...
I own a Surface Pro 3 which has only one USB-Port. Can I set up nRF-Connect with the internal Bluetooth instead of using an USB Hub to connect two development kits?
To whom it may concern.
Ended up on the Nordic Semiconductor website, since I was trying to find a good manufacturer for a Health Smartband and software.
I represent...
Hello, I want to use multiceiver mode nRF24l01. For 4 transmitters.
When setting up the receiver, I can only receive data from the tube 0.
I can not understand how to tell...
Hi all, I'm working on SDK13.0.0 secure bootloader and I'm curious to know about
Why nordic defined, dfu service uuid(0xFE59) is 16-bit uuid and characteristics in...
Hello,
I am attempting to use GCC with Eclipse. I have installed all the tools, sdk, etc. and have also installed Mentor Sourcery CodeBench to get the Make and rm tools...
