I am using nrf sniffer for trouble shooting. But it always exit unexpectedly. Wireshark was still open but the DOS window got closed.
I am attaching the log.txt.
log...
Hi all,
I am using ble open mesh with pca10028 boards ble mesh is working fine.
I am developing a application that has to blink led in mesh( without any delay between...
I'm still on stack 8.0.0 so it might have been fixed since. I have noticed that if the other side de-asserts CTS the Nordic code will leave the TX asserted in a Break condition...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
Hello Nordic Community,
I need to know how to import my PCB design from Eagle to CST Studio to simulate it and I need to know if the simulation step will be useful to enhance...
Hi.
I'm trying to get Apple notifications to nrf52. And specifically to listen both regular ANS (for android) and ANCS (for iOS) events depending what sort of phone is...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi,
I programmed nRF52 DK with BLE_APP_UART_SAADC_TIMER_DRIVEN with AIN6 pin as input and is working correctly. But when I programmed the same code in BMD300 the adc count...
I'm running an nrf52832, using SDK 11.0 and the S332 soft device. I've had instances where it seemed my flash data, stored with FDS, was corrupt after a firmware upgrade....
Hi Nordic,
I am having problems knowing what exactly happens in the following situation:
I have a connection established between a master and a slave, and the master...
Hi,
I have started your tutorials and just complement this one. devzone.nordicsemi.com/.../
Now when I tried to download other programs on the development kit, I get...
Hi,
I have wierd experience about using float32_t.
This is my test:
When i use operations on float64_t i got:
0.0001s MAIN:INFO:init_finished
0.0001s MAIN:INFO:loop...
I have a program which uses two timers to flash an LED, alternating between flashing once every 5s for 15s, then once every 0.25s for 15s.
If I run this on the nRF52-DK...
Hello,
I am new to nrf51822 BLE. I am using MDBT40 (nrf51822 series). Complete project is powered by 12V, 2500 Mah lithium ion Battery pack. I want to monitor battery level...
Hi,
I know how to OTA a ble device, but how do this on a ble master?
Is there any nrf tool can OTA a ble master ?
dev environment:
SoftDevices:S130 v2.0.1
sdk: nRF5_SDK_12...
Hi,
we are using a ISP130301 module from Insight SIP (containing a nrf51822CEAA ) with a low power acceleration sensor ADXL362 , connected via SPI. SoftDevice is s130_nrf51_2...
Hi,
SDK: nRF5_SDK_12.2.0_f012efa
No softdevice
Example: nRF5_SDK_12.2.0_f012efa\examples\peripheral\radio\transmitter\pca10040\blank
and receiver.
I have running...
Hello,
I am using nrf51 and firmware is ble_app_gls. I have modified my code to work for dfu as well.
I am getting error as follows
.\_build\nrf51422_xxac.axf: Error...
I try to integrate the CoAP Server and TFTP DFU example code, and it works well.
[ENV]
IoT SDK v0.9.0
nRF52832 DK
According to the specification, the MTU...
Hi, dear support team,
I program the softdevice(S110,v7.1.0) to the nRF51822 devices(our product) by nRFgo Studio v1.21.1.3.
The nRFgo Studio shows a error message as...
Good afternoon.
I have 2 boards NRF51:
One as beacon (SDK 9), use example code "nRF51_SDK_9.0.0\examples\ble_peripheral\ble_app_beacon".
The other as...
Hi,
I have a problem using Secure DFU Bootloader available in SDK 12.1 on nRF51822_xxAA SoC.
Initilaly i was using nRF51 DK board and Secure Bootloader example in SDK...
