We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
Hi there. I'm Matthew!
I noticed that there were contests sponsored by Nordic in the past, such as
Startup Weekend, June 15-17, 2012
The Nordic Semiconductor App...
I can use nRF Toolbox as a central to test various nRF5 as BLE peripheral samples.
Is there any sample app (iOS or Android) to test the few nRF5 as BLE central samples? ...
Hello.
I am trying to turn off ACK in the example "esb_ptx". I have tried this in both SDK 12.2 and 14.0.
I try to turn off ACK like this:
static nrf_esb_payload_t...
Hi,
I am trying to establish a border router in my test Thread system (a part of infocenter.nordicsemi.com/index.jsp . I have the required Raspberry Pi 3B, but it is driving...
I'm using the 1.0.1 nRF Sniffer and 1.10.10 Wireshark on Windows 10 64bit. The firmware 1.0.1 is programmed to nRF51822 dongle using Jlink 6.12a. The exe works fine when no...
Hello everyone,
I want to integrate NFC to one of my projects and I am having a problem with the value of some of the capacitors.
I am looking into using the nRF52832. ...
Where can I download the example project that can be imported into Eclipse?
Tutorial: devzone.nordicsemi.com/.../
Broken link: ble_app_hrs
When I follow the link...
can't program nrf52832ciaa
I can connect the core through segger commander
I can erase the chip after push the download bottom in the keil 5 ,and erase the chip...
I have an nRF5- DK and I'm following this tutorial . I loaded the softdevice, I can compile, I can load the flash, I can see the output in Termite, I can change the code to...
Hello,
I have an NRF51822 custom board. I am trying to flash the code under
C:\Users\Home\Desktop\nrf51\nRF5_SDK_12.3.0_d7731ad\examples\ble_peripheral\ble_app_uart...
Greetings -
The (custom) device I'm working on has multiple possible serial interfaces. I thought "Hey, I've written entire operating systems before, I should just intercept...
Hi all,
i need to write in flash, and i try to use the example flash write of sdk. It works correctly but when i put it in my code, the writing register ( NRF_NVMC->CONFIG...
Hi!
I'm developing Thread mesh using nrf52840 with COAP communication. I would like to set a longer timeout and more retransmission tries in COAP. I saw this parameters in...
I am trying to use one of the example from NRF5 IoT SDK with RPi3 (kernel 4.9.41-v7+) but keep getting "permission denied" when execute command below:
echo "connect 00...
