We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
Hello there guys i been reading your 100 pg PDF for awhile now and im yet to understand or realize how is it that i add/place/create a payload or data to send/Tx via Master...
I am interested in writing a BLE central that reads data from multiple BLE Nordic sensors. The BLE central will be running on Embedded Linux which uses the BlueZ stack.
...
Hi,
I'm trying to get S110 softdevice (v8.0.0) working with RIOT. I had some issues (I couldn't initialize TIMER1 or TIMER2 until softdevice is setup & enabled) but I think...
i read devzone.nordicsemi.com/.../ that simple multiple saadc-s is not so easy.
I also looked at github.com/.../ble_app_uart__saadc_timer_driven__scan_mode to use multiple...
When I keep this function :
static void vMain_iInitDeviceManager_Exe(bool erase_bonds)
{
uint32_t err_code;
dm_init_param_t init_param = {.clear_persistent_data =...
Hi, everyone.
I've developed a custom board using nrf52832. I tested it and found that CPU core, GPIO and other peripherals work well, but BLE doesn't work at all.
I ran...
Hi,
Raspberry (SPI Master) -> NRF52832 (SPI Slave)
The code below execute event_handler of SPI with NRF_DRV_SPIS_XFER_DONE type. But RX buffer is empty. All bytes are...
Greetings,
I'm in the process of choosing a nRF52 module. I know of this link for the various modules www.nordicsemi.com/.../3rd-Party-Bluetooth-low-energy-Modules.
I...
Hello, I've been trying to get directed advertising and auto-connection working on an NRF51822 peripheral.
I'm using SDK V11.0 with SD130 v2.0.1
This is the scenario...
Hi,
I used the code ble_app_uart_c on board 10028 as a base for my custom board.
My board is nrf51822 QFAA based so I changed all occurances of nrf51422 to nrf51822...
Hello,
We are trying to communicate to this board ( www.adafruit.com/.../1697 ) that has nRF8001 at its core.
Unfortunately, our TX is only able to output BLE 4.2
...
I'm running on nRF51822, SDK 8 (not totally sure, I inherited the project), SD130 and mbed.
I've tried and failed with my own code to use pstorage.
I'm now trying a...
Hi. I'm using nRF51822AC, SDK12.2.0, S130.
The size of "s130_nrf51_2.0.1_softdevice.hex" in SDK is almost 300KB.
But chip's flash mem size is just 256KB. It's bigger than...
How is it used? And why to use it?
static nrf_saadc_value_t m_buffer_pool[2][SAMPLES_IN_BUFFER];
instead of
static nrf_saadc_value_t m_buffer[SAMPLES_IN_BUFFER];
Hi team,
we are doing project called indoor navigation using beacons.To get the good RSSI signal strength,in which position should i need to place the beacon. Can any one...
