I want to make sure I'm far from ever having a stack overflow event. Is there a way in the IDE or elsewhere to monitor this risk? The map file produced after a build?
I am working on BLE. I have created a service using read property(services_set_barometer_service_barometer_data(void *src, int size))
After connection is set-up i am calling...
Hello, I'm using the nRF51822 and tried the HID Keyboard Application (S110, ble_app_hids_keyboard) example. (Nordic\nrf51822\Board\nrf6310\ble\ble_app_hids_keyboard )
The...
Hi all,
I have a situation in which softdevice (s310 v2) seems not to forward events to my nrf app (bootloader running dfu) in spite of the fact that my iOS app sees the...
I am sending setup commands to a NRF8001 D device and I receive a command response with status of 0x89. This appears to respond to ACI_STATUS_ERROR_UNSUPPORTED_FORMAT. I cannot...
Hi I'm working on a school project and I need to send data from an accelerometer to a phone I'm currently able to update "dummy" data from my nrf51822 to my phone after following...
Working on an ANT project.
Switched a project from S210 to S310 to add BLE feature.
For the ANT part, there is no source code modification at all.
Sweet.
This is not...
Hi ,
I have recently bought a nRF5232 PCA10040 development kit and i am trying to interface nRf52832 development kit(Master) with AS3955(slave) over twi. I tested the twi_scanner...
Hi all
I'm trying to build a generator based on NRF52832. Outpit signals are: 8MHz clock and two latches signals highly sinchronized with clock - RGB_LAT and TXT_LAT. For...
Hello,
I have a question on how to calculate the capacitance based on oscillator relaxation for NRF52. For example, in the Csense_drv example, when pin is touched by finger...
Hi,
I have a working scanner and manage to require timeslots with the below timings.
Interval 300ms, scan window 50ms, Timeslot length 10ms.
But when i try to...
Hi,
Trying to implement a simple Hardware UART in parrallel with Ble on a custom board with mdbt42 Raytac module. I have the following compilation error:
*** Using Compiler...
I was trying to integrate mesh network into the ble_uart. I am using softdevice v7.3 and sdk6 with nrf51822. I followed the instructions given in the github link text
....
Hi, I bought an Arduino PrimoCore card and I read that you need to buy the Alicepad card. I can not find it on the net. But was it put on the market? Thank you.
Hi,
I have added new UUID (Service and Characteristic) into the uuid_definitions.json but it's not used in the application.
To try I put a error into the json file and...
Initialization:
The softdevice is initialized as in the BLE UART example. The body of the ble_stack_init() function is identical to the BLE UART example.
SPI is initialized...
I have two supplier for provide me nrf52832's based modules.
So I tested it and both is ok. The distance used pcb antenna almost the same (about 80m).
If I use on external...
My application is built using the nRF52832 device.
The system must only be "active" between certain times (5am through to 9pm).
I am a newbie and have no idea how to set...
Hi,
what are the minimal required steps to get the zephyr HCI-UART on a PCA10040 working with Linux BlueZ?
The steps I have so far [My host is Ubuntu 17.04]:
Physically...
Hello,
I am having troubles to run the light_switch example from the nrf5_SDK_for_Mesh_v0.10.0.
I am using PCA10028 boards with nRF51822. I didn't modify anything in...
I basically need clarification on the last point of this question , which seems to imply that:
the first time you call sd_ble_gatts_hvx() while the SoftDevice's transmit...
