Hi, could you please tell me if my assumptions below correct?
Measuring a (ratiometric to VCC) analog signal and selecting VDD_1_2_PS as the reference selecting AIN_NO_PS...
When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi, I'm using a nRF51822 as a observer/scanner for Eddystone beacons. This device is intended to scan up to 16 beacons, but under certain conditions (unknown at this moment...
Hello,
i use a nrf52 developpment board, with the SDK 12.1.0. I use the ADC example which use the ppi channel, my question is : it's possible to set the ADC driver without...
Hi all,
i try to log event in memory, and when connection is established read value from E2C and send to APP.
if i send characteristics when event BLE_GAP_EVT_CONNECTED...
I use the ble_app_proximity example of the nRF51_SDK_10.0.0_dc26b5e, the chip on my board is QFAAH00 . When I down load the code, it pops the windows "IAR Warning: Stack pointer...
I am learning BLE and trying to develop a Health Thermometer which can be seen in the nRF Toolbox
I am using Bluetooth Developer Studio but cannot get the nRF Health thermometer...
In SDK 11.0 it seems that in case pin 31 is configured as a button (using port events), nrf_gpiote_task_enable keeps triggering the port event due too a work around for OUTINIT...
I developing wearable product based on nrf52832. The product is act as a beacon and its location track by other fixed BLE readers to positioning it in particular defined area...
Hi,
I'm working on accelerometer + BLE application. My current configurations are nrf51822 and LIS3dh accelerometer chip, Protocol TWI, Softdevice 110, BLE service type...
Hi!
I'm trying to learn osTimerStart(), \ble_app_hrs_rtx.
Compiling was successful, and it is working.
If I set the timer interval shorter than 25 ms, the timer cycle becomes...
Currently i am using NFC tag type - 2 Text Record Example code and integrated in my work space. Now, i wanted to add write capability in the same code.
Is there any sample...
It looks like NFC_T4T_EVENT_NDEF_UPDATED gets passed as the event attribute in the nfc_callback function whenever a new NDEF message is written.
Is this expected behavior...
Hi,
I have an aconno module ( http://aconno.de/acn52832/) and I am trying to program it via DK52.
I wired the module as follows:
Module Vcc (pin 12) -> DK52 VDD...
Hi all,
I am trying to get the ble template of SDK12.2 working in eclipse using a managed makefile. The softdevice I use is s132 v3.0.0. The board is an evaluation kit...
Hi Nordic,
I'd like to know what the maximal current draw from the internal REG0 is to power external components. The only thing I could find in the datasheet that says...
