Hi there,
My nRF5340 application requires the use of SD card with DMA and BLE transmission. Howerver, as soon as I turn on the device, I get the following errors:
A...
I'm using NCS SDK v3.0.2 and trying to build the Matter Thermostat example for the target: ` nrf54L15DK/nrf54L15/cpuapp/ns ` However, the build fails with the following errors...
when I try to build a code for integrating sensor in nRF 5340 dk, this error comes, I tried even after installing cmake manually from the cmake website https://cmake.org/...
Hello,
I am using an nRF9160 to connect to a private network. My nRF9160 successfully attaches to this network.
However, when reviewing the logs from the private network...
Hello,
How can I put the nRF54L15 into continuous wave mode? And I assume after entering CW that I can freely change channels using the FREQUENCY register (0x708). Is that...
Hi, I'm currently trying to add an Actinius Icarus IoT board as LTE device at nRF cloud.
I already know my board IMEI (I got it by flashing the AT client sample and then...
Connecting nrf21540 to a nrf52840. 840 GPIO default state is input, input buffer connected. One of the 840 GPIO pins is connected to the 540 PDN pin.
1) If the 840 gets...
Hi there,
I'm testing the "saadc" example : <InstallFolder>\examples\peripheral\saadc
I haven't changed the code.
To do this, I use the nRF52840 with SDK 14.2 and s140...
Hello,
I am probably beating a dead horse here....
I am evaluating the PCA10056/nrf52840 preview DK and using the Keil/uVison 5.24.2 for that purpose.
I have found some...
How to have control(play/pause & previous/next) over the Google Play Music app via a BLE link. I know I need HID over GATT but I downloaded the official doc and I cannot understand...
Hi,
I would like to use the nRF52840 modules for moving nodes. However, I'm concerned that the modules will not be able to cope with high moving velocities to communicate...
Hello, after getting my nRF52-DK I first tried to program it using Arduino IDE according to this guide. Everything worked perfectly as I was able to flash new firmware into...
Hi, Does BLE IPSP profile limits the maximum channels a one? I tried to change BLE_IPSP_MAX_CHANNELS to two, but it results code crashing at nrf_sdh_ble_enable() API. Is soft...
I'm finding some issues in sending data from nRF52832 using UART.
I need to send a string of length more than 100 characters.but when i
try to send,only 94 characters...
hi, I am switch from sdk 12.2.0 to sdk 14.2.0, I could not find softdevice_ble_evt_handler_set() and softdevice_sys_evt_handler_set(). what should I do with these two? and...
Hi,
I'm trying to develop something for nrf52832 and was trying to use the s130 softdevice. Using Kiel uVision 5 i added all the necessary packs, but when I add s130 to...
Hi,
I have two devices and one host. When they are in close area both of them are pairing to one host. When I switch off host, both devices looks like paired to each other...
Having gotten through the hurdles of getting my IAR project to compile and run on Segger Embedded Studio, I am now seeing different behavior between the two IDEs while debugging...
Hello,
In my application (based on app_nus_uart example, with two NRF52832 boards), one of the cases is uploading/downloading files with sizes up to 10MBytes.
In my app...
Can someone explain the reasons/benefits of using the single vs dual bank BLE boot loader?
Actually, why isn't there a single bank BLE bootloader in the example project...
I have following code which should start the app_timer and blink the LED_1.
When flashed, the LED_0 turns on and I can see the "Started." log. But the LED_1 is not blinking...
