Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
Hi, Everyone
My development environment is sdk15.3, nRF52840, Keil complier
The link error file is attached below.
Also I am going to use AES-CBC method.
Which example...
I'm experimenting with the USB MSC example (SDK 15.3) on my nRF52840 DK. It seems to work well in the polling mode as delivered. However, when I try to run in interrupt mode...
I have a serial port set upp with the serial port library like this:
#define UART_PIN_DISCONNECTED 0xFFFFFFFF /**< Value indicating that no pin is connected to this UART...
Hello,
I am trying to get started with the 9160-DK. So far it does not seem similar to the 52840 so I decided to take to the "Getting Started Assistant" within nRF Connect...
Hi, I'm using nrf52832 and SDK15.3. And I'm using the ble_app_uart example. The device will go to sleep mode if there is no connection for 3 mins.
My questions are:
1...
I'm calling sd_ble_gap_adv_start after a connection disconnects to start advertising again and it's returning err_code 12... which is NRF_ERROR_DATA_SIZE. However, the documentation...
Hello,
I am currently working on a project that involves the host device to send configurations parameters over to the device. I was hoping the connection between in device...
Hello All,
We working on OTA features with nRF52810 using sdk16.0 . When we are trying to upload the firmware zip format through mobile its giving error "upload failed:Insufficient...
Hi,
I am new at mesh .I use SDK UART coexistence example to test, and I can scan Ble uart demo by nrf Connect APP. But I can't scan Mesh node by nrf Mesh APP. I've been...
I am trying to program the Nordic nRF51822 MDBT40 Series module to communicate to an STM32 processor chip. The way I understand the procedure is as follows:
First, I must...
I want to use mbed TLS backend in BLE stack.
For example, BLE controller will use AES(hardware accelerator, I think) to gennerate link key and encrypt.
I know that SoftDevice...
I am trying to step through the code of an example of the nRF5_SDK_16.0.0 on the nRF52840 board.
I downloaded the latest version of Segger Embedded Studio (v4.30c) and I...
Hi,
Working with hx711 library and want to add some function for taring. I have a problem that when i run my simple taring function, the function returns 0, but it should...
