Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SDKs do have docs in markdown format. What is the recommended tool to be able to access all the features?
Tried MarkdownPad2, but it fails for example on @anchor tag.
...
Hello,
I have a problem statement in which I have to generate a file for data that is received from UART communication and want to send it to the mobile application whenever...
Hello guys,
For last couples of Days, we were trying to connect with IBasis NB-IOT Network with nRF9160 DK.
But not able to connect it .Please see below Snap Short for...
Hello,
I am using nRF52840, SDK_16.0.0, SoftDevice S140 V7.0.1 and Segger for flashing the image. I am using ‘ble_app_blinky’.
I want to send packet with different...
Hi,
In our project we are using the adc pin (p02) for batttery level measurement.
The analog dc signal from the battery is connected to p02 pin after the voltage is...
Hello,
Our peripheral device has no keyboard and no display.
Yet we would still like to have the most secured way of communication.
For our application, we don't like...
Apologies for the newbie question. Does this BLE Module need a separate antenna to be purchased? Or are you supposed to design your own with PCB traces? Some BLE modules have...
I want to avoid the soldering of the inside (Becoz of production isse) pins that's why I'm using all the outer pins of the ic. But the problem is RESET pin is inside so can...
Hello,
I am using UART_1 in my program to comminicate with other sensor. So the data is read from UART_1 and print to UART_0. Now I want to communicate with other sensor...
Hi, I am using BMD301 chip on my custom board which schematic i have shown below,I need to enable UART as well as nrf_log in my application. For this I am using SDK 15.3 PCA10040...
I am getting small power spikes but cant seem to pinpoint what is causing them.
The smaller spikes in between the transmissions. (The wave is clipped from the top so the...
Hello,
Has there been any success with getting the python bindings for the pc-ble-driver running on openwrt? I've succeeded with the driver itself but not the bindings....
So with the errata in mind the RC oscillator has a accuracy of +/-500 ppm, while the XTAL on the nRF52 DK has a accuracy of +/-20 ppm. During the longest waiting period of...
I have your full eval board as well, I also have multiple NB_IoT sims from Vodafone but have not tried them yet. How do I get your Thingy:91 unit with your sim running please...
