I'm having some trouble successfully entering ON,IDLE mode. I have pared-down my application to do the following:
Initializes the app_timer using the scheduler:
...
I want to control GPIO toggle by PPI. Timer1 is in timer mode. CC[0] is 1000, and CC[1] is 8000.
I use compare[0] to toggle gpio18 by PPI. I also want to use compare[1] to...
Hi,
I use two evk board to connected and test the uart serialization sample(ble_s110_serialization), one is ble_app_hrs and one is ble_app_connectivity. But I have one...
I am getting get BLE_EVT_USER_MEM_REQUEST and BLE_GAP_EVT_CONN_PARAM_UPDATE event, when writing to ble device, sample code did not handle these event, and seems no document...
Hello:
Why do I erase SDK5.2 version of flash and read not, in SDK4.2 can. I tested nrf51_sdk_v5_2_0_39364\nrf51822\Board\nrf6310\flashwrite_example is a good example.However...
before i write the flash, it has been erased.so ,its value is all 0xff.
when i write 0x00 to flash address 0x0001,the value read out is not 0x00 but 0x01,and the value in...
Hello,
I try to run electron app with pc-ble-driver-js and I have this error:
Error: The module '\\?\C:\app\build\Release\pc-ble-driver-js-sd_api_v2.node' was compiled...
Dear Team,
I am migrating the ANCS client application from SDK-12.3 to SDK-15.3 version.
Please find my below observations in SDK-15.3.
Erase the flash completely and...
Hi All,
I'm developing my product based on nrf51822.
I was using keil IDE for that.but i wanted to develop it in Segger instead keil ide.
is segger is supporting for...
Hello, I am working on an IoT project. For this project , I need to send some data using BLE. I developed a firmware for this application based on the sample ncs/zephyr/samples...
HI ,
In our project we are using multiple gpiote and app timer interrupt.
SDK we are using is 15.3
DOUBTS
If both gpiote and app timer interrupt trigger simultaneously...
Hi,
I'm using nRF mesh library v1.2.1 and integrating into my mobile application which I am developing, I implemented provision functionality without errors but sometimes...
I am bringing up a custom board based on the PCA10040.
As the first step, I simply copied (no changes) the file pca10040.h and named it as "my_custom.h". I then defined...
We have an nRF52 DK system running ble_app_uart_c example code and communicating with a peripheral device. We setup a second development system using another nRF52 DK system...
I have the nRF52840-DK with the adafruit PN532 RFID/NFC shield installed on top of it.
I run the TWI Scanner and receive a report that a device was found at address 0x24...
I am having a strange issue with my custom radio protocol. I have ported the code to the 52840 and SDK15 from the nrf51822 where it is running with no issues.
The issue...
Hello,
I have PCA10040 development board with nRF52832, Softdevice S132 v6.1.0 & SDK 15.1.0). I wanted to use the extended advertisement feature to advertise more than 255...
Hi,
After developing two application, one for emitting extended advertising and other one for scanning this kind of advertising on nRF52840 DK (Github repository here: MOTAM...
Hi,
I would like to ask two questions.
1)
I understand that the nrf52832 does not support the feature "Transmitter has a Stable Modulation Index".
But the component...
Hello, I am trying to build the asset tracker reference app for my newly acquired Thingy:91.
I went through the instructions to get the toolchain and SEGGER IDE up and...
