Hi, I'm currently in architecture definition stage, and I'd like to know more about the possibilities driven by Channel Sounding. From what I understand, you can only perform...
Hi,
I am encountering an issue with the TWIM driver when attempting to communicate with the nPM1300 PMIC via I2C.
This problem seems to be related to the behavior of the...
I have been trying to implement a way to wake the system up after doing sys_poweroff() but no matter what nothing seems to work. I already tried many examples and none of...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
The custom AT command "AT%XICCID" was added in modem firmware v1.1.3 for the nRF9160 and was available from the first release for the nRF91x1.
This command provides a processed...
Hello,
Is the NRF7002 pre-certified for the RADIO EQUIPMENT DIRECTIVE 2014/53/EU (RED directive) ?
Is there a recommended antenna design that would ease certify a product...
Good day, I was attempting to test the radio performance of the NRF54L15. I ported over the Radio_Test sample project to try and transmit an unmodulated carrier wave at a...
It seems that the version of the soft device used in the mesh sdk does not match the version of soft device SDK that I can download, and the version used in the mesh SDK has...
Hi,
I am trying to run the examples for the pc_ble_driver_py and I get some issues.
advertising.py says "board not found"
heart_rate_collector.py gives a calledProcessError...
Hi folks,
I want to do a project from scratch using the Segger compiler. Where can I find relevant documents with it. How can I make changes on the Blinky project? For...
Hello,
I have two version of Python 3.6 installed: 32 and 64 bit (Windows 10)
Recently i installed nRF5x command line tools (9.7.2) and pynrfjprog 9.7.1
For Python...
In zephyr many PPI has been employed in radio, and other PPI from 20 to 31 is pre-programmed channels and can not use by application. Do you have any plan for optimize this...
hello,
I have one problem to distinguish the following 2 functions :
ble_srv_is_notification_enabled and ble_srv_is_indication_enabled
in on_write function,
the two...
Hi Nordic
I saw the Dfu example.
BLE Secure DFU Bootloader and Buttonless DFU Template Application. I have two questions here. The boot loader and app distinguish a ram...
I'm getting a weird behaviour on my first NRF52 custom board. It's a BLE with HR, battery and a custom service. After programming I can test it properly with/without debugger...
Hi,
I am using SDK 14.0 on nRF52840 (DK), with sofdevice enabled and FreeRTOS port.
My question reagrds the "blocking mode" transfer - event handler was not provided...
I have four PCA10056 Development Boards and I downloaded the SDK for BLE Mesh. The examples, however, only work with the PCA10040 boards. I have tried redefining the board...
Hi all,
We are ready to have our product released and need to have it tested and certified for release in the following markets:
North America = FCC IC
Europe...
Hello,
I would like to configure the NRF51822 as a Peripheral to receive data from a smart phone, and then call a routine when the receive process has been terminated....
I'm using the nrf52832 and I need to stream audio from an SPI connected memory chip, to an I2S connected amplifier. Is there a way I can have the SPI device stream data directly...
Hello,
i have the following setup: nrf52 as peripheral, smartphone as central.
Peripheral's purpose is to be an interface between appliance and smartphone. It has no pairing...
