Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hi, i'm using two nrf52840 DK ev kit. One it's the central and one the peripheral
After the connection I need to save power at the peripheral board, because the cpnsumptio...
In mesh example project “dimming_server”，I have added functions: mesh serial, SAADC(use ppi) and compie pass.However,when debugging,an error is happened in the function"nrf_drv_timer_init...
NRF52840 support the long range bluetooth and BLE gateway SDK, look at here that RAK Wireless held a Beta and welcome the community to participate.This board with Cellular...
Good day!
Started to work with nRF mesh. And wanted to add ir_lib from this project to Generic OnOff example.
And Source navigator shows error: static_assert failed "unspecified...
I tried to use UART both for NRF_LOG and NRF_CLI. Now it's running but I had a problem that calling to nrf_cli_init caused fatal error 8 - INVALID_STATE.
When I commented...
i have question about nRF52832's bluetuth. xtal is 32M, Cload is 12pf, but the frequency is 2.402199G(tested by Network Analyzer), Frequency differency is 199K. We find that...
Yes I've already looked at the following two examples:
https://devzone.nordicsemi.com/question/185381/disabling-pin-21-of-nrf52832/
https://devzone.nordicsemi.com/question...
I'm currently working on a board diagnostic firmware and an accompanying Windows console app. The Win part of the project is supposed to monitor the diagnostic firmware's...
Hi,
I am trying to run the light switch example of the nRF5-SDK-for-Mesh-v1.0.0 on total 3 boards(1-client and 2-servers). I changed the no. of servers as mentioned in...
Hi All:
i want to change mesh net key to apply different client.
but when i change net key to {0x5f, 0x5f, 0x6e, 0x6f, 0x72, 0x64, 0x69, 0x63, 0x5f, 0x5f, 0x73, 0x65,...
Hello,
I ran light switch example on nordic boards & i am able to send light turn on/off command from client switch but i also want to configure my light servers to able...
I am using nrf_drv_uart library.
UART communication is set in non-blocing mode, and transfer od data is relised with nrf_drv_uart_rx and nrf_drv_uart_tx functions.
I am...
I am trying to run pb remote example but i'm stuck at command 3 it only shows "Got event 0" not goes further to receive remote uuid.
0> 1) Provision first available device...
Hi, Everyone
My development environment is PCA10040 (nRF5_SDK_14.2.0_17b948a) with IAR
The printf statement is output to the terminal (Teraterm) using the UART. However...
Hello,
Our company is considering on developing BLE products with Bluetooth 5.0 compliance in mind. I'm currently trying to get as many information as possible but I'm...
Hi,
Once applying 0V to DEC2 pin, CPU hangs up and cannot be system resetted even though we input reset signal to RESET pin.
The only way to reset is to suppress system...
I am new to Nordic and BLE mesh connectivity. I have the following assumptions & queries, Please clarify if I am wrong.
1. Is it possible to implement BLE Mesh using Thing52...
I'm trying to read data over UART as fast as possible using the double-buffering feature and EasyDMA, but even this simple example I've posted is losing data.
I've set up...
