I have a simple GATT server application with two characteristics, RX and TX. In my prj.conf, I am trying to disable pairing as follows :
I can connect to the server from...
Hello,
I am trying to use LTE connectivity on a custom board with a nRF9160 SICA B1, but i am facing issues with the modem.
With both my own app firmware and the sample...
I have searched all responses here and whatever sources I can find, but not have any success. The main problem is that existing materials appear incompatible with the 54L...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
I am attempting to do some development using the usbd_hid_generic example peripheral code. I am using some C++ libraries in this project, however there is syntax in the usbd...
I would guess that's basically the whole point of the structure, but I want to make sure that the location of the SoftDevice Information Structure and the relative positions...
I want to use the nrf24l01+ with the se2436 apmlifier, but the input of the amplifier requires an input of 100ohms balanced, while the nrf24 has a balanced output of 15ohm...
Hello,
I am using following component for my project, 1-nrf51822,2-SDK 11 3-S130, 4-BLE400 board, 5-Keil IDE. I am also using SDK 11.x HID example for my base program....
Hi,
I try to use the nRF sniffer but it doesn't display anything.
System used :
Windows 10 Family x64
Wireshark 2.4.4
Python 2.7.14 (in C\Python27 included in...
When the Softdevice is not enabled, can the nrf_nvic_ functions be used? When I never enable Softdevice but call err_code = sd_nvic_ClearPendingIRQ(RADIO_IRQn) I get error...
I am working with the DK-52 and SDK 14.2. I am generating two PWM signals using the pwm driver.
Everything works as expected on PINS 11 and 12.
If I change pins to 5...
I'm using nRF52832 SDK board with softdevice s132_nrf52_5.0.0 and SDK 14.2.
The program compile without an error. I tested the led and timer separately and these work.
...
Hey all,
I tried to build my project in the Keil µVision IDE.
But everytime I get the same error and I can't figure out where the problem should be.
I searched for the...
I would like to call sd_power_system_off in my error handler. The product is at a stage where occasional errors still occur as the devices are deployed "in the field" for...
We have a custom board solution with an BLE module from Laird, that uses nrf51822 IC, as a gateway. Code was written in Keil and we used SDK v 8.1.0. Originally we didn't...
According to BLUETOOTH SPECIFICATION Version 5.0 | Vol 3, Part G page 2248
Exchange MTU procedure is initiated by the Cilent, and only be initiated once.
But by looking...
Hi,
I'm trying to add the peer manager to my project, following the guidelines at infocenter.nordicsemi.com/index.jsp
I've copied the peer_manager_init() function exactly...
