I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
Hi.
I am using the NRF52 Development board, on Keil uVision, to implement a C program that uses Dynamic Structs. The Structs re-size themselves ( by increasing their capacity...
Hello,
I have an NRF51822 (redbealab ble nano) that I would like to use to count pulses in very low power mode.
Pulses are asynchronous
The rate of pulses can...
Hi
I'm attempting to read a PT-100 sensor value that is part of a voltage divider using a nRF52.
Both the reference resistor and the PT-100 is sampled while the voltage...
Hi
I have been searching the forums, but were not able to find an answer to my question.
I'm trying to sample 4 analog inputs on the nRF51-DK using the ADC hal. (SDK10...
Hi
I have been trying to get two NRF24L01 chips communicate with each other since a week now, without much success. All what I can find on the net is Arduino examples using...
Hi
I have done several projects with the nRF905. I know the device quite well. Normally I use the CD, AM and DR interrupt pins to determine the status of the device, my current...
Dear Sir,
Please tell me how to configure the NFC pine P0.09 & P0.10 as GPIOs. I followed all the procedure given in the development kli manual & on the nordic blogs also...
Dear Sir,
I am using nrf52832 & sdk 14. When I dump your twi sensor code(SDK14\nRF5_SDK_14.2.0_17b948a\examples\peripheral\twi_scanner\pca10040\blank\arm5_no_packs) in the...
Hi ,
Need a bit of help here.
I am trying to use TWI and SPI in a single code for communicating with two different slave devices, the LTC2941 coulomb counter and the EM4325...
I've adapted the SPI example to read a value from an Analog Devices ADXL350 accelerometer as follows:
But when connected to the accelerometer this hangs waiting for the...
Hi, DevZone,
I am trying connect nRF52480 Preview DK and an Arduino UNO CAN Bus shield.
What I did is:
1) I directly hook CAN Bus shield on the top of nRF52480 Preview...
Hi,
Does anyone know where to download the old SDK versions? I tried to search it in Infocenter, but there I only found the manual documents and API reference, not the SDK...
How slow will an nrf52832 run, using an external crystal, for the purpose of extending battery life? Or am I looking at the wrong processor? I'm looking for a processor for...
Hi everyone!
I'm new to this platform and researching if it's right for my game studio. What I am looking for is a list of boards that have compliance, ideally in the EU...
Hello!
SDK15's DFU with app_scheduler is great!
I am able to Select, Create, and Write an Init Packet. On Execute, however, I get "Flash erase failed (0x3)". What might...
Dear All: My board will reset some time, and i print the register "RESETREAS", and It's value is 8, the PS says it is "cpu lock up detected", Could anyone tell me what will...
Continuous input of audio stream at ATX , but intermittent output audio streams at ARX. why?
how can i use data channal? Once data (three bytes) is sent at ATX,Receive data...
I try to use the SDK 11.0 for my nrf52832 dfu function . But i encountered the error as below:
I am using the ANT_s332_nrf52_5.0.0 .
Any advice . thanks
Building configuration...
Hi all,
I am using SDK14.1.0
Steps of my execution are -
1) My requirement is to make bond when making connection to the android APP. I have done following initialization...
