Hello,
I established a connection between my central and peripheral module. Now i want to write characteristic value on peripheral. I tried with sd_ble_gattc_write function...
I am using the NRF24l01 for my products and looking to buy in bulk(100-1000). Now I know where to buy the just the IC but antenna design is a hard point to break right now...
Hi, my friend,
I've been with nrf905. I use a 16-bit CRC check.
But I encountered problems in use:
1.Nrf905 16-bit CRC check format is CRC-16(IBM):X16+X15+X2+1 or other...
I have two custom PCBs, each of which has a microcontroller and an nrf24L01+. Everything related to the transceiver in the designs are complete duplicates (with the exception...
Hello,
I've built a small BLE-device based on the nrf8001.
With my Iphone I can discover this device and I am able to connect to it and listen to notifications of the...
Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
from this guide
https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader#h23sjziacp7vrw0scs2t3tua1ax0426
It is...
Good evening.....
I am looking to play around with the Thingy 91 but I am a hardware guy who knows enough about firmware to be dangerous. I typically run into issues getting...
Hi,
I am trying to send firmware image from one board to another board. For that I want to use DFU control point characteristics.
I am using nrf52832 development kit...
I have installed the cocoapod for nrfMeshProvision, but i am new to BLE technology. I am able to fetch the dataIn and dataOut characteristics, but stuck at creating a Proxyhandler...
Hi,
I have a project where we want to setup 3 PWM channels for dimming LED strings in a mesh configuration. So the mesh dimming server is a perfect starting point. I did...
Hello,
Our team is new on development nRF52832 firmware.
Now we have an issue on standby current for nRF52832.
We have a 5 second timer for a PWM output.
Sleep (System...
Hello there,
I am facing some difficulties while using nRF52832 NFC for an application.
When I tap the nrf52832 device on the NFC reader the nrf52 cannot able to respond...
Hi, we are currently looking at making a zigbee light switch using the 52811. However since the zboss library files are compiled with FPU directives the only way to build...
I need to read data from sensor and publish it to the mesh network. So the question is do I need to create Sensor model for that or, as in one of your replies , you suggested...
Hello Nordic Team,
I want to connect peripheral using Mac address, i am setting mac address filter in Scan init but Filter is not getting set
below is my Scan init function...
Hi there,
We have a network of zigbee with XBee-PRO modules working as co-coordinators and end nodes. I have to use BMD340 zigbee node to join that network as well. We have...
Do you have any example which is using NRF_SDH_DISPATCH_MODEL_POLLING for advertising, as well as scanning.
In nrf_sdh.c file, there is only interrupt mechanism in example...
I have an nrf52840 dongle. I can enter into DFU mode and the nRF programmer application recognizes it and shows the memory layout.
When I copy sniffer_pca10056_129d2b3...
Hi,
I am using nrf52832 for advertising and scanning. My board stops advertising after disconnecting.
I am calling all initializations (like ble_stach_init() ) from my...
