Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
I am a started guy.
I only need a bluetooth device (BLE) to check the signal and mac address.
What is the best choice?
I need the smallest and low powered!
Thank you...
I am working on code to setup a bond manager for ancs based off of the example, but have a fixed advertising and connection interval of 25ms. How does the bond manager and...
Hello,
My thingy:91 is publishing its messages to nrfcloud (=to the corresponding AWS mqttEndPoint and topics/ I suppose AWS IoT Core).
Now I want to get/process these...
In the example / serial in SES I see the softdevice is loaded as an "additional load file"
$(SDK_ROOT:../../../nRF5_SDK_16.0.0_98a08e2)/components/softdevice/s140/hex/s140_nrf52_7...
I am quite new to the nrf9160. Trying to run the gps example https://github.com/ExploratoryEngineering/nrf9160-gps . But everytime I get an error Failed to start GPS. I am...
Hello, the SDK example ble_peripheral\ble_app_uart includes the code below in order to forward data from the UART over the BLE. What it does is wait for a CRLF, or a certain...
hello
i have created 1 custom service for that created 3 characteristics.
with that 3 characteristics i'm trying to notify by using nrf connect app.
my question is...
We are looking for a BLE-enabled chip which can bind to a smartphone, with the aim of performing proximity tests. to make sure the person in possession of the chip is indeed...
We want to design a small tracker for key rings like car keys etc, it will be linked with mobile app. Is it possible to do so?
Whatever I have read till now is it is possible...
Hi,
We are planning to run the nRF52840 in CKAA configuration 3 (attached) in Normal Mode. When we boot, our regulator will provide VDD = VDDH = 1.8V. Reading through the...
Our product is using NRF24L01+ and PA to transmitter data. It pass all the test of FCC PART C but the BAND Edge measurement.
The below 2 pictures is NRF24L01+ Band edge...
Hello everyone,
I have been dealing with this issue for some time now, and I think it's time to find a definitive solution, I am sure there is one!
For my projects,...
I had some questions when using nRF5SDK160098a08e2\examples\dfu\secure_bootloader\pca10056_s140_ble for OTA test. Who can help me answer my question?
1. Can I return the...
Hi,
i have created some custom characteristics and i am enabling read and write characteristics in that, but when i am trying to write or read some data it seems that it...
Hi everyone,
I am trying to connect my nRF 9160 DK and Thingy:91 to TIM (Telecom Italia Mobile) CAT-NB1 network provider from Brazil. I am using the Asset Tracker and...
Hello,
For my project I want to use broadcast packages to send data to multiple devices at the same time.
I've seen that there is a beacon application that "should"...
Hi,
I'm trying to develop a custom service and am following a few examples in trying to do so. The software crashes for me everytime after advertising the new service...
