Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
Hi,
I'm using nrf52832 (SDK 15.3). And I have 24 chips on the same I2C bus. They all work fine right row. But if one of the chip is broken, the whole system will crash....
If a reliable mesh transfer is ongoing the node will crash with a mesh assert at access_reliable.c:373, in access_reliable_cancel_all().
This happens because access_clear...
Hi all,
I am looking for the Objective Product Specification for the nRF52840 chip. I have only found the Objective P roduct Specification for nRF52832 in version 0.6.3...
After setting up my Peripheral Mode I am also looking at ways to improve my current design. I would like to ask about Mesh support on the NRF Thingy 91 integrated with the...
Was anybody able to connect to HTS (Health Thermometer Service) on iOS applications, OTHER than nRFToolbox or LightBlue? Which applications did you use?
I tried a dozen...
Greetings....
It is great that you provided SDK UART coexistence example for nRF5 SDK for Mesh v3.1.0 and nRF5 SDK v15.2.0 release for Client node with nRF52832 DK. However...
I am trying to build an example code for PCA10040, but I always have a lot of compiler error: C:/Program Files (x86)/SEGGER/SEGGER Embedded Studio for RISC-V 4.42/source/thumb_crt0...
Hello,
I'm working with the Nrf52832 Dev Kit and the ble_uart_example. After flashing with the hex file and powering the Dev Kit, the on-board-LED starts to blink. Now I...
Hi Nordic team,
I am currently developing a concurrent wireless application with BLE and a proprietary protocol using the timeslot API.
My setup:
nRf52840 DK
SDK...
Hello, guys!
We are working with SDK 15.0.0 and nRF52840 SoCs.
There is a need to transfer a few MBytes of data from the PC to nRF52840 and then on external flash memory...
Hi
this is the code I'm trying with my buzzer,
I want it to generate sound but with different frequencies.
".base_clock = NRF_PWM_CLK_1MHz," I can only as low as 125kHz...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I am trying to combine the examples ble_app_uart...
Hello.
I am trying to run the throughput example for the Connect SDK, using a 52840 DK and a 52833 DK.
https://github.com/NordicPlayground/fw-nrfconnect-nrf/tree/master...
With sdk16 cli, each command displays help message when used with -h option. It would be nice to have a help command which can display all active commands and their help ...
Hi,
I would like to use raytac MDBT50Q-U without an 32 mhz external crystal.
Periphal examples like "blinky" work but ble does not? nrf_sdh_enable_request fails with invalid...
