Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
In ble_app_blinky_pca10040e_s112 example, Generic access service has read and write permission.
When writing the name, I want to handle this event and change the advertisement...
Hi Team,
We are using nRF52840 DK with the latest SDK 16.0.0. We know that SDK have multiprotocol support for BLE+thread and BLE+zigbee. Its okay for that and we tested...
Hi, i have been trying to get GPS and HTTP to be able to work with eachother, but im having some struggles.
After the GPS starts, the program begins spewing out "Invalid...
Hello,
I have exercised the flash driver and that is working fine. I want to save a certain value into a specific address in NVM and I want that part of the .hex file. I...
I just upgraded to SES 4.42 from 4.30a and I'm getting the following compiler warning for file zigbee_cli_cmd_ado.c "Taking address of packed member of struct zb_af_simple_decs_1_1_s...
Dear Sirs,
I am using example anr_hrm nrf_sdk_15.3.0 I would like to use PINs on/off
software s212
#include "nrf.h"
#include "nrf_gpio.h"
#include "nrf_delay.h"...
Dear All,
I am using (nRF52840) in one of my design.
Application program we have taken examples\peripheral\usbd_ble_uart\pca10056\s140\arm5_no_packs code as base code...
Hi,
Good Day!
Statement of Problem: We are using SPI to transfer data to custom LED matrix which uses HT1632C led driver. For strings more than 7 character length we used...
I want to integrate nrf mesh serial example in light Switch example to configure other un-provisioned node
I am using following nrf SDK: >> nrf : nRF5_SDK_15.2.0_9412b96...
Hello,
We have evaluated Smart Remote 3 example code .We migrated that code in the segger embedded studio but we are getting lots of error related to files and libraries...
Hi, I have nRF9160DK and Thingy:91. I want to store APN configurations in the modem but I can't save the APN. Currently, I am giving the APN information manually every time...
Hi
I have nrf82540 dev boards. I loaded one board with Proximity example (SDk Version: nRF5_SDK_15.3.0).
According to your web page: https://infocenter.nordicsemi.com...
I am working on a project that needs to be a ble central and peripheral. I based my development off the experimental/ble_central_and_peripheral/ble_app_hrs_rcs_relay however...
Dear Sirs, good afternoon
I am working in a design that includes an nRF52840 as main processor.
I need to know if it is possible to have the following peripherals implemented...
Hi,
How do we fuse the debug port on nRF9160? The purpose is to block all access and the ability to erase all from outside.
This is my understanding:
From debugger...
