I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
Hi, I'm a newbie to Nordic and need to use multiple nRF24LE1s to get ADC values and transmit them to a single nRF24L01 connected to an Arduino. I need sample Keil compiler...
HI:
i hava a sender and it send a frame every 15ms ,not use any protocol,and reciver code like as follow:
while (1) {
Rf_StartRx(ReciverSC.RfBufPointer...
Hi to everyone,
i have an mb39c811-evsk-02 and over it there is a tmp102 temperature sensor and an nrf51822.
I want to read the values of the sensor over a beacon app. ...
Hi,I'm glad you can see my post.
Now, I am in a program to read and write FLASH such as the screenshot in the attachment.
Then I update with DFU service for the equipment...
Hi Is it possible to change the MTU size with the Master Control Panel?
I am making a ble device on a nrf52 with the SDK 12 (latest softdevice) which has the ability to...
Is there a function like battery_level_in_percent for AA battery?
I know battery_level_in_percent is only for CR2032.
Even though I compensate it to make it 3V from AA battery...
Hi,
I'm currently evaluating the nRF9160 chip as a potential replacement device in our internet-connected products. In most cases the zephyr documentation and examples are...
Hi,
I modified your USBD BLE UART Example by commenting out the button and LED code to run on a dongle with J-Link debugger soldered on.
I removed the bootloader and set...
Hi I am new to NRF52832. I am using SDK 16, Multlink Central (ble_app_multilink_central).
Here are my questions:
1) The software keep resetting when I flashed the code...
Setup nRF52840 DK S140 nRF52 SDK v16.0.0 nRF SDK for Mesh v4.0.0 Goal I would like to be able to disable the Mesh stack and all radio operations so that my application can...
Hi,
[Softdevice 6.1.1]
I am developing an application which uses the radio timeslot api in conjunction with BLE. Even without starting BLE advertising, or any other BLE...
I did some evaluation on nrf9160dk recently. I try to run some at command to control lte modem, but some wired thing happen.
After I introduce at command in to one work...
Is there is an option to change the payload of NFC t2t after setting the payload.
So the requirement is once there is a polling device is in the field, we need to change...
In ble_app_blinky_pca10040e_s112 example, Generic access service has read and write permission.
When writing the name, I want to handle this event and change the advertisement...
Hi Team,
We are using nRF52840 DK with the latest SDK 16.0.0. We know that SDK have multiprotocol support for BLE+thread and BLE+zigbee. Its okay for that and we tested...
Hi, i have been trying to get GPS and HTTP to be able to work with eachother, but im having some struggles.
After the GPS starts, the program begins spewing out "Invalid...
Hello,
I have exercised the flash driver and that is working fine. I want to save a certain value into a specific address in NVM and I want that part of the .hex file. I...
I just upgraded to SES 4.42 from 4.30a and I'm getting the following compiler warning for file zigbee_cli_cmd_ado.c "Taking address of packed member of struct zb_af_simple_decs_1_1_s...
Dear Sirs,
I am using example anr_hrm nrf_sdk_15.3.0 I would like to use PINs on/off
software s212
#include "nrf.h"
#include "nrf_gpio.h"
#include "nrf_delay.h"...
Dear All,
I am using (nRF52840) in one of my design.
Application program we have taken examples\peripheral\usbd_ble_uart\pca10056\s140\arm5_no_packs code as base code...
Hi,
Good Day!
Statement of Problem: We are using SPI to transfer data to custom LED matrix which uses HT1632C led driver. For strings more than 7 character length we used...
