void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
I have some problems with the TWI (I2C) and it seems that TWI1 does not send anything. I have managed to create a simple example to recreate the issue. I am using TWI1 instead...
Hello.
Is it possible to send more than 1B data via blinky characteristic from central to peripheral? I made my project with two characteristic (my own 128-bit UUID) basing...
I am using android ble with kotlin. I ported the Blinky example to kotlin. There is a reference escaped in object construction when on construction the BLEManager invokes...
Dear Nordic Team!
I am verifying my tools chain for nrf52840 Mesh project development by mesh light-switch example. I have 4 PCA10056 and make them to 1 provisioner, 1 client...
Hi,
I use sdk16 and nRF52832.I want to change advertising in the air:
Now I'm using the timer to change the adv.But I want to change adv with RF interrupt.
Like this...
I developed an application (BLE named Adriano) using nRF52840 DK, nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730, starting from ble_zigbee_dynamic example. I added some custom...
Hi,
I'm developping an application for nRF52840 as a BLE central. It is supposed to connect to an Android device (BLE peripheral) using a bond (encrypted connection with...
Hi everyone,
I went through the source code by Vidar Berg for background dfu using SDK 15.3. I am working with nRF52832 , S132 and SDk 12 with Keil IDE. I did try with secure...
Hi,
I am currently developing with nRF52811 chip using nRF52840 DK. Where can I find a reference 2.4GHz PCB antenna design document?
Thanks.
Regards,
Jxq
Dear Team:
Hi team,I just want to know:
1.Can the ESB protocol call the frequency hopping of Gazell? Is there a corresponding description and source code?
2.Can the...
hi, i am facing this unknown error at "unknown function at 0x000008C8",
i am doing a development project with nrf52832(sdk14.2 and s132v5,ble nus is used) mcu and sim800...
Hello, I'm developing SAADC on nRF52832.
While developing, I have problems now.
I applied sine wave on ADC input.
And the result is displayed on the figure that I...
Hi:
Use the nordic official nRF52832 development board , The software is SDK15.3(example: ble_app_uart ),
Find that there will be a continuous reset. What is the problem...
Hey all,
I am trying to run the "nrfx_spim" example on my nRF52840 USB Dongle (Makerdiary nRF52840 USB dongle), however it is not working. It looks like the code is never...
I have been testing the softdevice codes on NRF52840 DK with NRF52840 SDK 15.2.0 which is working perfectly. But when i put the same test code in our custom board having BT840...
