We are developing an application on nrf52840 and wanted to use M95P32 as external flash.
used below .overlay configuration to enable it on zephyr.
&mx25r64 {
compatible...
This ticket is the continuation and related to the previous ticket on the matter: https://devzone.nordicsemi.com/f/nordic-q-a/121669/enabling-the-tls-layer-to-get-a-https...
Hi,
Using nRF Connect SDK 2.7.0 on an nRF9160. Using native tls, works fine, i can setup HTTPS connections.
Problems arise when i try to use MQTT with native TLS (with...
Hello Nordic DevZone community,
I have been working with the ZBOSS stack on the nRF5340 and understand that it has version management and migration features for persistent...
SDK 2.3.0
We have a custom board with a few GPIO connected to various interrupt sources (Button, sensor interrupts, power connection etc.)
We are experiencing here sleep...
nrf52820 custom board
nRF5_SDK_17.1.0_ddde560
s112_nrf52_7.2.0_softdevice
secure_bootloader_ble_s112_pca10100e
I tried to incorporate ble dfu to my application but...
Hi Team,
Excuse me. Where can I find the reliability test reports of the following four models? Thank you!
nRF54L15-QFAA-R
nRF9151-LACA-R
nRF7000-QFAA-R
nPM1100...
Hi there,
I am now in FCC stage and finalizing a FCC code using the radio test sample code. I do have a delimma on what type of radio mode I have to use. Will you please...
Hi,
I am working on a school project, and I need to use a nRF51 dongle as a BLE master. However, when I try to use JLinkExe to connect to the dongle, it fails all the time...
Hi am using NRF52 board ...and am trying to send data(which is not a string) using ble_bus_string_send . I send data only once from a one second timer but the other side is...
Hi all!
I'm working on an nrf51822 (technically right now I'm using the PTR5518 as I'm still prototpying), and trying to set up a voltage divider on my pcb in order to...
Hi,I am debuging my programm base on SD-110-V6.0.0 ,sdk-V5.2.0. When I use the
static void characteristic_disc_req_send(const ble_ans_c_t * p_ans, const ble_gattc_handle_range_t...
Hi everyone,
I have a nrf51-dk. I am running Master Control Panel app on my win7 computer. However, I cannot see my nrf51-dk in discovered devices section. Log says, Loading...
I am working on an application for the nRF52 Preview board, using SDK 0.9.2. I need to acquire about five analog samples from a single channel at roughly 100 Hz, then wait...
I use SDK9.0,SD8.0,the device is 51822AC,the device can enter to Bootloader mode.
As it shows below.
Then I selected the .zip file to start DFU
But when it reached...
I'm trying to do all my development on linux, mostly so that I can use a continuous integration environment. I'm setting up a server to compile my firmware app on every pull...
Hello I am currently using the NRF52 DK2 PCA10040 with S132 soft device (nRF52 SDK v0.9.2) . I have setup my code to sample 4 analog pins periodically. I configured double...
Hi everyone,
Well, our device is based on NRF 51822 CFAC MCU. It’s an ibeacon based device which advertises and receives data frequently, and writes data into flash memory...
Hi,
I have a project that uses PStorage and the Nordic UART Service. PStorage is used to store a variable that is updated by the device, irrespective of the Bluetooth,...
Question:
From ble device I have to send some data or character to mobile in connected mode. After sending that data the device is not going to sleep mode while connected...
I'm trying to modify the beacon properties of the nrf Beacon in the nRF Beacon APP but it doesn't allow me to change those properties.
If I use the Beacon scanner the device...
I am trying to find out the part number of the antenna (I assume it is a PCB antenna) used in the nRF51 DK ( www.nordicsemi.com/.../nRF51-DK) . I found a lot of similar questions...
