Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
NRF52840
S140
APP based on ble_app_multilink_central
1 PCA10056 as central, 1 PCA10056 as peripheral, the cantral can find the peripheral and buid connection.
But...
I had the nrf5340 DK working for a few weeks now, and while working with SSD1309 OLED peripheral, was trying out a simple display application. Couldn't get the display device...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
Hello everyone,
I compiled the nrf51-app-button-examples without any error and warnings but it is showing me this error (No cortex -M Device found in JTAG chain / Target...
According to PCA10028_Schematic_and_PCB.pdf (Rev 1.2.0), page 7, there should be SB22-25 surrounding TP5-8:
On my PCA10028, I have TP5-8, but no SB's there:
What...
Hi All,
I'm having a problem with my application which involves regularly sampling I2C slave data and sending it over Bluetooth. The I2C slave generates an active high...
It looks like the RTC0_CONFIG_FREQUENCY define in nrf_drv_config.h which is located in nearly every project may have a typo. The define is listed as 32678, and the RTC1 define...
I am seeing a problem identical to what's described in this question . I'm using SDK version 10.
My timers work fine for a while, but then suddenly and seemingly at random...
Hello, I am trying to build Smart beacon kit firmware from sources.
From ble_app_beacon folder I have built the firmware using armgcc (with the proper makefile) and got hex...
Hello,
The documentation states, that "maximum consecutive TX time is limited"
17.1.9 Maximum consecutive transmission time Maximum
consecutive transmission time...
Hi,
I have a JLink script which sets APPROTECT in the UICR to enable readback protection and disable the debug interface.
For development purposes, I would like to be...
Hi,
I tried to use nrf51822 to update light intensity of 64 area to smartphone and then the smart phone will display those light intensity values in gray scale. I want...
Hi everyone!
During the development of our device, we faced with some problems:
So now we need to read the data array in a clear sequence from characteristics. The data...
Hi,
I have a device running firmware from SDK10 and using s110. I would like to update the device to use SDK11 firmware with S130v2. I'm using following code to generate...
Hello,
my application hex used to work fine before i change my bootloader and softdevice
now after falshing all the hex including the application , it is advertising as...
Hi,
I want data read from my sensor (gives continuous data when button is being pressed). and then send it through Bluetooth equipment.(PC or iPhone and so on) But i don...
nRF51_SDK_9.0.0_2e23562
S310
/*
* Setup the gpiote to handle pin events on the MMA8451Q INT1 pin. For the
* accelerometer we want to detect high->low transitions in...
hello everybody,
I'm working in a project & have to do something like security for the connection & be able to do updates to firmwares, someone suggested that doing bonding...
