Hi all,
i want to establish connection between two threads in cmsis-rtos, can i use
1) semaphore to do this?
2)message queue should be used or any other ipcs can be...
Hi,
I have two CPU in our product. (STM32F2 and Nordic nrf51422).
I use serialization function to link those two CPU(refer to ble_s110_serialization sample)
But I find...
Hi,
My behavior is as follows
Turn on my device(use 51422) and advertising(2 Service and 3 Characteristic)
Turn on my cell phone(Samsung Note3),scan my device...
Hello:
I used analog IIC write MPU6050. Again after power download programs, mpu6050 can run up there ACK response. But the debug will not run. Simulation IIC because no...
Hello!
How can I communicate with my nRF24L01+ and nRF51822 at the same time. I can set up same channel, CRC-mode and I don't use ESB. But what about address? How do I set...
Hi all,
i want to know answer related to following question
1)what is use of uicr?
2)if i place some value in uicr and then change the image,then is there will be change...
It used to work, but now it says "Connected" but the rest of the GUI never changes and the mouse just shows a busy spinner. Here's the log file:
0;13:45:18.9900 [MainThread...
When compiling C++ code that includes ble_gatts.h you get errors like the following:
C:/....../nrf51822/Include/s110/nrf_svc.h:21:6: error: impossible constraint in...
Hi,
I can execute the heart_rate_collector example code on Ubuntu PC when driver is communicated through Segger JLink. But I'd like to use GPIO pins of nRF51-DK as communicating...
Maybe I should post my all the code here.
I want to generate two kinds of PWM1 and PWM2,used by the code as follows:
static volatile bool ready_flag;
APP_PWM_INSTANCE...
Hi everybody.
I make an application which combine ANCS and NUS services on PC100028 (nrf51 SDK 9.0.0)
This application works properly when I use IOS device which installed...
What does it mean if I set my advertising timeout with this macro (which is equal to zero)? I would expect that it would advertise forever but instead sd_ble_gap_adv_start...
The latest TWI example I can find is from 4 SDK revisions ago and uses old libraries. Is there a sample using the nrf_drv_twi library that is recommended for current development...
I'm experimenting with the relay as well as hrs and rscs demos. Basically, I want to check at startup for IRKs stored in flash on startup in the peripherals. I'm only working...
I have developed my custom board and my custom application based on nRF51822 and S110-v8.
It perfectly works with Master Control Panel v9.0: connection, bonding, dfu,......
Hi,
I am interested in your nRF51 IoT SDK, IoT SDK for applications using IPv6 over Bluetooth Smart.
The presentation www.youtube.com/watch describes an architecture...
I'm developing an application supporting concurrent central and peripheral connections and using the new Connection State module in SDK 10 to decide whether a BLE stack event...
Are there any modules/devices with sar certification for the nrf51?
I have a need for something that will be placed with an elastic band against the arm or upper torso...
Hello,
I am using S110 8.0 stack and 9.0 SDK and I am testing the signal strength.
Now I am able to get the BLE_GAP_EVT_RSSI_CHANGED event after I started performing rssi...
Hello,
I am investigating the on_ble_ev function and trying to get back the Connection Interval parameters set by the Master Control throught the ble_evt_t struture . Is...
Hi,
I want to use the NRF51-DK to program an external device. It worked fine so far using the J-Link Firmware. I had to switch to mbed since it is a huge mess to get it...
