Hello,
I am working with the DWM3001CDK (nRF52833 + DW3110) using SDK 17.1.0 . I have successfully compiled and flashed the DTM example.
I am trying to use nRF Connect...
this is my prj conf
# Bluetooth
CONFIG_BT =y
CONFIG_BT_BROADCASTER =y
CONFIG_BT_OBSERVER =n
CONFIG_BT_PERIPHERAL =y
CONFIG_BT_DEVICE_NAME = "Range extender"...
hi support team,
if customer want to certificate device with 21540, which tool can customer use for dtm testing?
our tool can only set it to 8, can't be 10, as below:...
I am working on a project where I am using the npm1300 with host nrf5340. The BUCK1 powers a sensor and BUCK2 powers the nrf5340. I have a SPDT switch connected to GPIO0 and...
Hi,
Is it possible in BLE channel sounding in ncs 3.0.1 to get some information about the quality of the distance measurement for each method? We have three ways to get...
As shown in the figure, MCUboot has a boot_go_hook function. I'd like to define this function in my own project and compile it into MCUboot. Since I'm using single slot DFU...
We are developing HW that includes nRF9151 running DECT NR+ with the Wirepas stack for mesh connectivity between multiple units. The product is expected to move between geographies...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Heading ##Here my PCA1000 board is getting detected in nRFgo studio even i can program and debug it, But i cant see COM PORT.
Can anybody help me out in this...
When i...
Hi,
I'm trying out the nRF52832 with kit PCA10040 V 0.9.0. I have S132 softdevice installed and running the ble_app_pwr_profiling example from nRF5 SDK v11.0.0.
I'm...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
I am trying to manage the bonds as follows. I've defined the max bonded masters as 4 on my slave. When this list gets full, I delete a random bonded master on the slave (not...
I'm trying to flash to a device with the GCC toolchain using "make -f Makefile flash_softdevice" and nrfjprog fails with the message "ERROR: There is no debugger connected...
Hi.
I've searched this forum and also the code for pin muxings. One of post here said that any gpio can be configured for any output. However how is this done in code?...
I have a peripheral device based on the nRF51822, s130 and SDK 11.0.0. It's designed to only ever have one central device to which it's bonded. Out of the box, without a bond...
Hello.
I have a question.
I want to use UART without flow control.
In this case, I don't know what to set rts_pin_no and cts_pin_no of app_uart_comm_params_t.
Please...
I use nrf51822qfaa,s110,v8.0.
now i use the TWI master.the nrf_drv_twi_tx function always return 0x03(NRF_ERROR_INTERNAL),WHY?WHO can help me?
code:
nrf_drv_twi_t twi_instance...
Hi all:
I refer the "IoT_SDK_step_by_step.pdf" to setup my raspberry_pi ,then I can successfully ping the DK_board from raspberry_pi.
my question is , I can't ping the...
Hi everyone!!
I've gotten the ipv6_coap_server example to run on the nRF51-DK,and I use raspberry pi as gateway and I can got the bt0 interface after connecting to the...
I would like to add LIN-bus to a project of mine.
The hardware part is easy, connect a LIN interface ASIC to the UART of the nRF5x.
But writing my own LIN-bus SW driver...
