My eval setup is PPK2(source mode) -> nPM1300EV - -> nRF54L15DK. I have my load connected to BUCK2, everything else is disabled.
I'm getting higher than expected input current...
I am currently attempting to send HTTP requests (GET and POST) with my nRF9160 DK over an LTE connection. I have tried running the HTTP client sample code under zephyr/samples...
Hi,
Currently, we develop a prototype that needs to communicate with WuR; the FH101RF. Could you please tell me if it is possible to communicate with it? If not, can you...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hello, could you please provide me an working example of TCP socket communication using Thingy:91X by LTE-M/NB-IoT?
I haven't found any (only UDP and I need TCP).
Thank...
Hi,
I am using the nrf54l15 on a custom board in our current project and want to use it with DFU over BLE FOTA as well as TF-M.
I can compile the project just fine before...
I used Nordic52480 DK(bulb) as DUT to run Matter Certification case TC-DGGEN-2.1 .
Steps:
1. setup OTBR on Pi4：./certification-tool/backend/test_collections/matter/scripts...
Seeing the Log on wireshark for Central and peripheral communication after connection.
Here i am bit confused that when Connection update request is send by Slave after...
Hi, I try to access Generic Access to get device name.
So, I modified "ble_bas_c.c - ble_bas_c_init()" like this.
bas_uuid.type = BLE_UUID_GAP_CHARACTERISTIC_DEVICE_NAME;...
Hi,
I want to find Bluetooth address of the Central Device which is running Master Control Panel Application....
but after succeful connection, each time I try to find...
I am using serial communication to have data from a sensor. That sensor only can support baud rate 115200 to communicate. Collecting data from that sensor I am trying to save...
Hello Everybody,
I have read these articles on the site : article_1 &
article_2
I need to do something like that, read around 8000 sample with sampling rate equals...
Hi,
I used the app of nordic , that puts the system off in order to measure the current at that mode.
the example i used is at this link . ( system-off-wakeup-on-gpio...
Hi
I'm very new and looking at the PTR5518 breakout board. The docs below specify some of the pins:
Are the pins EN , RX , TX , RTS etc. tied to P0.08, P0.09,...
Dear Sir/Madam,
I want to use the One channel of Timer 1 for PWM generation and other channel is used to measure the pulse width of input square wave.
For above i need...
When I try to step through my code, I get a wdt event firing. I have tried setting the behaviour to pause during debug and sleep
void wdt_init(void)
{
uint32_t operationStatus...
I would like to measure BER and PER on custom board by using sample project that is included SDK.
\examples\dtm\direct_test_mode\pca10028\s110
Could you please teach...
Hello,
I'm powering a Readbear BLE nano using a CR2450 coin cell battery. The firmware application is written using mbed. How can I measure the battery level of the CR2450...
hi,
can i use timer interrupt has more than 1ms period??
#define APP_TIMER_TICKS(MS, PRESCALER)
((uint32_t)ROUNDED_DIV((MS) * (uint64_t)APP_TIMER_CLOCK_FREQ, ((PRESCALER...
Hi, I'm trying IOT SDK now and I got some questions
My devices: nRF51422 DK, nRF51_iot_sdk_0.8.0_f1f6187, iot_ipv6_coap_client_pca10028
Q1: Why is the advertising interval...
Hi Nordic support,
I am building the ble_connectivity project of the latest SDK11. My EVB is pca10028m, the project is located under "nRF5_SDK_11.0.0_89a8197\examples\ble_central_and_peripheral...
