Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
Hello,
I sae that there is the possibility to upgrade the modem via FOTA/OTA application (for example asset_tracker), now without touching the modem could be possible to...
Hello,
Are there any hardware constraints or hard forks in putting an older version of an SDK, such as v11.0.0, on a much newer chip?
I'd like to port SDKv11.0.0 to...
Hello,
Is there any existing firmware where the nRF9160 can act as a coprocessor -- accepting AT commands and the ability to forward LTE data to and from a host application...
Hello, i am a beginner, i am parsing a dimming example. i have two client and server boards, as well as an nRF Mesh application. I can change the brightness of LED by pressing...
Dear Sirs,
I have dveloped application based on the ANT rx HRM example and with nrf52 SD board works perfectly (pca10040(
I would like to move to this application into...
I am using ble_app_gls s130 SDK_11. Is it possible to have pairing with static passkey without bonding? This is because the nRF device will be connected to different smartphones...
I am working on the nr sdk for mesh application,When the nodes conncted to the network , it needs to configured before using nRF mesh app ,My device also configured through...
I am using nRF52840 with nRF5 SDK for Thread and Zigbee 1.0.0 on the nRF52840 development kit.
The Release build of the mqttsn_client example compiles and runs fine.
Using...
To start, this was a functional unit and I had been installing test firmware into it.
As of a couple of days ago while attempting to read and write to my nrf5340-PDK module...
Hello,
I am using pc-ble-driver-py 0.14.1 running on python3.8 and Ubuntu Desktop with nRF52840-Dongle. Dongle is running connectivity_4.1.1_usb_with_s135_5.1.0.hex. Dongle...
Hello,
I would like to understand difference between Manufacturer ID (5 bytes), used in ble_dis_sys_id_t type and Company ID (2 bytes) - used in advertising of manufacturer...
Hello,
we made a custom board using the chip nRF51822 and were able to use the template project in \..\examples\peripheral\template_project to make a button switch the led...
Hello,
I can't set the memory map into segger with a zephyr project.
For example for blinky project into ncs/zephyr/samples/blinky.
When I go to Project->Options, I...
Hello, we use the nRF24LE1 (24 pin) in a product, that is in production since many years. In order to process a FW change request I need to test the FW on a nRF24LE1 (48pin...
Dear Devzone
I have an NB-IoT application running on a Thingy:91, that wakes up every two minutes and sends a small package over TCP to a remote server. I'm using a Keithley...
