Hi all,
I am using and nrf9160, in particular a thingy91. It is running 1.3.7 firmware. I have the SLM sample loaded and can sent AT commands to the device using the nRF...
Hi,
I purchased a Qorvo QM33120WDK1 UWB development kit that uses a Nordic nrf52840-DK. I have been using this DK for weeks without issues, but the last time I used it...
I'm trying to add diagnostic logging functionality to my Matter project using SDK version v3.0.1. I followed the steps outlined here: ( https://docs.nordicsemi.com/bundle...
Hi,
In one of our future hardware designs, we have a MPU (running LInux) connected to a Bluetooth SOC over a serial interface (uart/spi/...).
Our first approach was...
Hello,
I have been able to get FW OTA to work perfectly well over BLE using
CONFIG_NCS_SAMPLE_MCUMGR_BT_OTA_DFU =y
Now I am trying to display the update progress...
Hi there,
I'm working with a custom board based on the Raytac AN54L15Q module and encountering higher-than-expected power consumption when trying to profile using the system_off...
Hi,
1.In ncs v3.0.0, can both USB DFU and UART DFU be enabled simultaneously on the nRF5340 DK board? 2. If USB and UART DFU can be enabled simultaneously, then how should...
Development board: nRF54L15DK i I'm already using "Find My Example" to connect to the "Find My" app on my iPhone. At the same time, I also want to connect to nRF Connect....
Hi,
there is my project rom size in memory report , I would like to asking what is the "NO Paths" item and hidden item
they hold my 20% ROM size. and what is the content...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Dear All,
I updated Toolchain and SDKs to last version v3.0.2 and I'm going to add build configuration as suggested here How to create and build an application .
My board...
Hello,
I am trying to modify peripheral_hids_keyboard 's security configuration as Security Mode 1 Level 2.
According to some Q&A thread, I tried the following:
1...
The nrf_cloud_multi_service sampe is running in to fatal error while trying to downolad A-GNSS data. The sample is configured to work with NB-IoT and CoAP.
Here is the log...
hi support team,
may i ask how to set static ip address for 7002?
1. i set these configs:
CONFIG_NET_CONFIG_SETTINGS =y
CONFIG_NET_CONFIG_NEED_IPV4 =y
CONFIG_NET_DHCPV4...
Hey everyone,
I have designed a custom board with a bunch of nordic IC's (nRF54L15, nRF9151, nRF7002 & nPM1300)
I have tested the basic functionality so far, including...
Hi，
Platform : nrf52840, NCS 2.7.0
I would like to get the MCUBoot image swapping progress without modify the NCS, and display a progress bar on the LCD to indicate the...
Hi everyone,
I'm new to both nRF Connect SDK and Zephyr RTOS , and I’m trying to modify the official LittleFS FileSystem Sample to mount an external SPI flash as the storage...
