Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hello everyone,
I’m working on a project using two nRF5340-DK boards to measure throughput and RSSI while dynamically changing the PHY and TX power. I started from the official...
Hi
I am working with nrf52832 development kit. I am trying to write device information service from central device to peripheral device.
I am successfully able to write...
Hello Devzone,
I've been using nRF52810, SoftDevice 112 (5.1.1), for a Mic recording application. What I'm trying to do is sample PDM MEMS mic data through PDM interface...
Dear Team,
I have nRF52 DK and nRF52840 DK, Can we program nRF9160 using nRF52 DK?
Please let me know the process and detailed wiring to program nRF9160.
Ashiq Moha...
Hi,
Good Day!
Statement of Problem: We use Li-Ion Battery in our application and would like to monitor a few variables such as Battery Voltage, Battery temperature & Discharge...
Hello, I'm trying to set up SPI communication with a sensor from my nrf5284_pca10056 running zephyr.
This is my prj.conf file:
This is my .overlay file:
And this...
I'm looking at the GPIO functions in http://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/zephyr/reference/peripherals/gpio.html , and looking at the function prototype...
Hi
I'm have and NRF52840 with a MPU9250 connected via TWI. The connection to the MPU9250 is successful, I can find its address on the bus (0x68).
I've implemented a very...
I am trying to add to an existing project gpiote
I have copied the code from the example project and tried to add all the files and changes to my sdk_config.h to match the...
Hello all,
I'm trying to develop a basic bike computer, compatible with ANT+. For that, I'm using nRF52 DK. My main objective is to be able to connect to any commercial...
Hello,
I have nRF52840 with code that is based on SDK16.
I am not using Softdevice in my project - just MBR , Bootloader and Application.
I was able to upgrade my code...
Hi all,
We are successfully using the nRF52840 chip in one of our projects except for the DFU functionality. We tried following these tutorials without success:
devzone...
Hi, I'm dealing with the ble long_range_demo. Central packet gives arrival time and rssi signal through the rtt viewer. However, I am willing to know the sending time of the...
Hi all,
I am investigating Mesh SDK and interoperability between devices.
We have bought some Hytronik devices which are qualified with Bluetooth.
Strange thing is that...
Hi,
I am new to thread network. In my application only a few nodes, mostly one. How can I connect this one node to the internet? Assume WiFi is available.Can I use the thread...
