We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello, I am experiencing issues with the current measurements taken by the PPK2 when using the nPM2100-EK to power a device. The current drawn from the 2.7V power source ...
I have been trying to get MQTT+TLS to work on the nRF7002 DK and haven't been able to get the samples to connect to the MQTT Broker.
Is there a working MQTT TLS example...
Seeing the failure below and wondering a couple things:
How did the device get into this state?
How do I disable AP protection? The Kconfig GUI seems to indicate that...
As far as I know there is a restriction in older bluetooth versions for number of slaves in a star network. 6 slaves can access same master, totally 7 units in a star topology...
Hello everyone,
I've been reading about BLE dev kits lately for one of my projects. I purchased the BLE Mini by RedBear Labs and had a good time with it... till I started...
I have an nRFgo motherboard on which I can set the VTG voltage to anywhere from 1.9V to 3.3V using nRFgo Studio. I'm trying to get a UART connection working to a GSM modem...
can ble_flash_page_erase return an error_code if erase uncuccessful? ble_flash.h show that it can ,but the code of ble_flash.c seem that it can not
uint32_t ble_flash_page_erase...
I am working on a project which is currently based on the nRF51922, and I would like to look at the S310 specification document. I found a link on this page: www.nordicsemi...
This is not a real question for support. It's more a success story i'd like to share with you!
Our company develops firmware for various customers on a lot of different...
Hi,
I'm trying to set up an iOS app (which I know is working properly) with a nRF8001 using nRFGo studio. I do not have the nRFGo dev kit (only the 8001 dev kit) so I hooked...
Hi
How to set device address in nRF8001?
I only see get device address command.
Does it mean I just only put my device address in MCU?
Thanks.
BR
Atlas
Hi,
I'm trying to generate some time variant values for testing purposes... rand() always returns 1447534768! This is in the proximity app FWIW.
So, I thought I would...
nrf24le1 memory map shows that there are two sram block size of 512byte ,the first one is data retentive (address 0-0x0200) ,another one is data non retentive (address 0x0200...
My device use the firmware program ble_app_uart to connect the nexus 7 which Installs the nRF UART 2.0 for Android 4.3 。The first connection is ok，and Data sent and received...
Hello,
I am a beginner in the world of bluetooth and bluetooth smart connections. I am working with an nrf51822 Evaluation kit an android phone (Nexus 4 running 4.4.2)...
Is it normal that after cutting SB8 our chip is still working when connected to USB port? (in case of battery we need to connect pin 1 and 2 from P1). I spend long time looking...
