void in_pin_handler (nrf_drv_gpiote_pin_t pin, nrf_gpiote_polarity_t action)
{
nrf_drv_gpiote_out_toggle(PIN_OUT);
}
This function work with interupt event (push...
here I have a very strange problem. I m trying to send the data(1 byte) from slave to master,and I have to use the multilink demo because I will have 2 slave devices.
The...
I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
We have run the Hello World program on the nRF5340-PDK, but now following the basic steps to program the heart rate example, there is no BT broadcast for Zephyr Heartrate...
Hello everyone. I'm creating a setup function to configure LSM9DS1 accelerometer and gyroscope by writing to the corresponding registers as shown below
Although this code...
I use sdk16.0 and nrf52832.
Can you give me an example of nrf52832 timeslot example ? thank you.
I read timeslot on DevZone,but many routines are missing files, resulting...
Writing an app for the Arduino Nano 33 BLE Sense:
https://store.arduino.cc/usa/nano-33-ble-sense
Basically I am reading all sensors on the Sense board (temperature, humidity...
I have programmed a Nordic Thingy 91 with lte_ble_gateway, and when I send command from the cloud to the device, an NRF_CLOUD_EVT_RX_DATA event is called, however evt->param...
Dear all,
I want to implement multiple functions with only one power button, including: 1. Power on/off, Long press to turn on, long press to turn off; 2. Functional response...
I am trying to connect nrf52840 dongle to multiple peripherals(nrf51822) ,so far i combined multilink_c example with uart_c and i can connect and read rssi value of only 1...
Sorry, my English is very bad.
I think I can only express my problem in Chinese.
在使用异步串口时，使用uart_rx_enable()设置的超时时间和真实发生UART_RX_RDY事件的时间相差巨大
using async serial port...
Hi,
We need to interface camera (0.3nrf52840MP to 2MP) with nrf52840 for a new product development. For evaluation purpose, is there any off the shelf camera module which...
I'm trying to add a timer to the usb_cdc_acm example to send a periodic text messages with the timer. I'm building on an Adafruit nRF52840 Feather Express board using Segger...
Hi ,
I am trying to parse the manufacturer specific data that a beacon is advertising.
I can read successfully the company_id but unable to read the "specific data " ...
Hello again Nordic Pro's,
As you probably all know by now, our product app is based on the subject example code, SDK and device. We need to programmatically disconnect from...
I have been trying ti debug with SES and re-installed everything trying to get it to work, for a while it did, but then it began showing this message:
also, it asks me...
Hi All,
I am working on nRF9160 GPS profile. built the code with Segger version 4.16 and updated the latest mfw_nrf9160_1.1.1 modem firmware.
when i compile try to catch...
