I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hi,
I recently checked support of MCUBoot validation and from NSIB for nrf54l15. (sdk 3.0.0 and above)
During this, I enabled Signature algo as ecdsa-p256.
And...
How to prevent storage partition from erase durning MCUBOOT firmware update?
I use Settings with NVS to store data
CONFIG_FLASH_MAP=y
CONFIG_FLASH=y
CONFIG_SETTINGS...
Hi,
I am building a Thread network ( www.youtube.com/watch with a Rasp Pi 4 as a border router, an nRF52840 DK as an RCP, and an nRF5340 DK as a child to be added into the...
Hi,
I am trying to change an example code on ble_app_uart_c (Central) SDK10.0.0 s130.
I have changed already peripheral example and I can see notification data if I...
Hi,
while flashing the device i get "Contents mismatch at: 0001C1C0H".
I am not sure if my IROM1 and IRAM1 settings are setup correct in the Target Settings of my Keil project...
Hi,
i have two microcontrollers: STM32F401 and nRF51822. They communicate by uart with flow control. I use 110 Soft Device from SDK 10. The maximum baud rate when communication...
Hi All,
I am trying to update the HEX file of LED_mesh example using DFU bootloader over-the-air. The LED_mesh application HEX file gets uploaded successfully by bootloader...
Hi Nordics,
I copy pwm sample code into my proximity project, to drive a buzzer .
I init pwm before softdevice. but, once "SOFTDEVICE_HANDLER_INIT" is excuted, the buzzer...
Hi,
i have a problem with nRF51 an nRF24LU1+. I use S110 and micro-esb library. I can switch beatween poroperty RF and bluetooh ( never run both in the same time ). When...
I wanted to use the SysTick timer for timing in my application, but even when writing a handler and trying to set it up, it doesn't seem like the interrupt is ever triggered...
hi I am i using Keil to debug the progam, it seems like that the printf() function can't work in keil, so i use jlink RTT to perform the printf function to collect data ....
HI,
i want to have a application in which a timer timeout say 5 second. and during this timeout there is another timer say 1 second. whenever the 1sec timer timeouts then...
Hi,
The function sd_ble_enable(ble_enable_params_t * p_ble_enable_params, uint32_t * p_app_ram_base) requires now the application RAM base address! Is it 0x20002800?
Hi ~
I use nrf51-micro-esb on GitHub
In Tx-Device: auto sent (data+1) to Rx-Device
But Rx-Device receiver data still the same not Increment....
why in Rx-Device...
Hi everybody
Since quite a long time since my last visit here. Now I come back because a new project using the NRF51822. Because now I'm using the NRF51822-CEAA, I can...
Hello,
I am developing an application where in i want to create a network with One central[not a mobile,pc,tablet etc] and multiple peripherals connected to the central excahnging...
HI,ALL
my Project can not exit the GPIO INTERRUPT HANDLER.
following is my project.
include "nrf_gpio.h"
include "nrf52.h"
include "boards.h"
define BUTTON_1...
