SDK_9.0.0
I was trying to implement 2 different UART connection parameters so I decide to use re-initialization.
My initial parameters included APP_UART_FLOW_CONTROL_LOW_POWER...
I'm trying to use the nrf8001 (and arduino) to send MIDI (musical note data) to Mac OSX. According to the Apple developer site the midi profile requires that the characteristic...
I have a custom made board that has an EFM32WG360F256 communicating to an nRF8001, verified that the ACI protocol works with repeated echos, however when I run the efm_ble_my_project_template...
Hi,
I have 3 nRF51 DK pca10028 v1.1.0
I compiled and run power profiling example and after that I cannot flash or connect to the devices (tested in all three of them)...
Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
We are currently working on a project using Enhanced ShockBurst (ESB) and would like to enable Front-End Module (FEM) support with the nRF21540.
According to the Enhanced...
Hello Nordic,
We have recently purchased an nRF52840 Dongle. We were able to sniff the BLE packets over the air. So it is found that all the packets that we are able to...
I wanted a COAP Server running on nRF5340dk with DTLS and NS-Target without success. Whenever there is an attempt to connect to it from outside the app freezes, eg. shell...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hi
I want to use nRF54L15_DK run RSSI test
I know Desktop App on PC "RSSI Viewer" only Support nRF52 series,
Q1：How can I use Desktop App to run RSSI test?
Q2：Can...
I am currently working on a project involving the nRF52832 SoC using nRF5 SDK v15.0.0 . According to the nRF52832 Product Specification v1.4 , it is mentioned that P0.00 ...
I am receiving packets in monitor mode on a nRF7002DK. I need some advice on how to interpret the signal value. From <modules/nrf_wifi/fw_if/umac_if/inc/system/fmac_structs...
I'm developing a solution using the nRF9160 and would like to confirm the correct method to completely disable NB-IoT mode so the device operates exclusively in LTE-M.
...
Hi,
I have a custom board build with an nrf9151. Right now I'd like to have the possibilty ti get modem trace. But it's look like I got crypted/corrupted data from UART1...
By default the GRTC peripheral is not cleared when started via sys_clock_driver_init . This is because nrfx_grtc_init calls nrfy_grtc_prepare , however NRFX_GRTC_CONFIG_CLEAR_AT_INIT...
Hello everyone
I created a custom board with reference to thingy:91 for the antenna part. The board is 50x50 mm in size.
I tested the board and there are no problems...
Hi,
currently I'm migrating my application from SDK5 to NCS and I'm facing a problem with the application size for a BLE update. In the previous SDK5 there was the softdevice...
Dear Experts,
I would like to better understand what exactly is accomplished by the mode-0 synchronization in Channel Sounding. My current understanding is that it seems...
