Hi
i use nrf51822 s110 "hrs" example to transmit the data to ios.
I need to add an option to send back some data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hi
i use the hrs example to transmit the data to ios.
but i need to add an option to send back data (from ios to nrf51822). 10 bytes maximum .
how can i implement...
Hello,when i get connected to the phone,when i call err_code = ble_hts_measurement_send(&m_hts, &simulated_meas) and err_code = ble_bas_battery_level_update(&m_bas, battery_level...
I got the Dynastream N5 kit and have successfully used it with limited ANT work and was trying to get BLE working but can't get a driver for the USB dongle. On the 51422 product...
Hi All,
I am working in the sleep mode with system off and wake up with internal RC clock.
It function well when connected to EV board...
I see the "Emulated System...
I want to write PCA20006 nRF51822 Beacon Firmware to PCA10004 on nRF6330.
I understand need to modify GPIO.
PCA20006 firmware consist of 3 firmware, SoftDevice, application...
Hi,
I'd like to connect my nRF2740 to my MCU Arduino Micro and test it with the sample codes found in your GIT repo. How can I do this?
Best regards,
Alessandro
Sorry for the silly question, but as it is mandatory to use sd_X function when it is possible to avoid collision, could you tell me if this code is the right way to use the...
hello all, i need a Bluetooth low energy peripheral device in which i can attach a single button to in order to control simple phone operations, i'm not sure what device will...
Hi,
I need protection against the MITM attack, what should I modify in heart rate example? Actually, I change the characteristics to BLE_GAP_CONN_SEC_MODE_SET_ENC_NO_MITM...
Hi!
I am using nRF51822 evaluation kit and connecting it as a master to a pair of I2C-devices (using twi_hw_master.c). Everything works well, but when I integrated the...
Hi,
I am using the Evaluation Kit, and I have tried to send some data between the Developoment Dongle (PCA10000) to the Evaluation Kit board (PCA10001). As the Development...
Hi,
Are there any reference design for interfacing a nRF51822 with an external sensor for e.g. an accelerometer (STM LIS3DH, AD ADXL362 etc)
Also do we have a profile...
My application would like to receieve notifications at several different times before a radio notification event. Specifically the application needs to receive notification...
Hello,
i have two operation modes:
One or more devices are bonded and advertising mode with whitelist (BLE_GAP_ADV_FP_FILTER_CONNREQ)
A new proximity central device...
Hi all,
From this forum and the examples given in the "sdk" find two approaches to measuring the battery voltage:
using external divider 10M/2.2M+22nF
using integrated...
In the previous discussion you told me to buy Mod nRF-8001 from olimex and i was also very optimist after going through its design that it can easily be connected to Arduino...
I have an application in which I would like to be able to enable and disable the SoftDevice.
But there are peripherals (Application Timers, Two Wire Interface, etc) that...
Hi,
I'm using PCA10001 connect to a sensor chip.I would like to set the register values for sensor chip as SPI master role and I need to switch to slave role to read the...
Hello,
i just want setup 1Tx and 1 RX using NRF24L01+ chips. but i am confused what should be Transmitter side Tx & Rx and what should be in Rx Tx & RX ? in order to use...
Hi,
There were similar questions already anwsered but none of them work for me. So the situation is as follows. When i program the chip though SWD interface the chip probably...
