after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Dir Sir. I am checking the current profile of nRF24AP2 in RX mode.
After "open channel" command, I found the peak current at 10ms interval until connection pass.
How does...
Hello,
I am using Nordic's UART service to communicate with my project. I use iOS and also Master Control Panel (with a dongle) on a laptop.
I have two questions:
...
SWI*_IRQ is using by softdevice to send event to application, I want to know which priority does softdevice set for them?
Does sd_nvic_critical_region_enter() disable...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
Hi, Is there any resource or sample project to print the thingy:91x onboard sensor values to the serial using the printk? I tried myself with
#define BME680_NODE DT_NODELABEL...
Hello,
I'm working on a project using the nRF52840 and Zephyr, and I'm experiencing an issue when trying to use device power management (PM) with a custom sensor driver...
I am working on stm32 f7 using nrf7002 . My requirement is to work my code on zephyr IDE as same as wifi shell. but for these when I going to add configuration for nrf and...
Hey,
the USB connection to my nRF54L15-DK isn't working anymore.
It is not showing up in nRF Connect Desktop and I can't find it under /dev/tty... or /dev/cu...
The...
Hi,
I'm developing an application on the nRF54L15 and recently I designed a custom PCB with a sensor that gives interrupts when its FIFO is full (should be around every...
I'm working on a project using CBOR, and Nordic's zcbor library in particular, to help with the serialization of data structures that need to be transmitted or stored. We...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Hi,
I am currently evaluating the nRF54L15 dk and porting the old project code from the nRF52DK to the new nRF54L15DK devboard. However, I have encountered an issue with...
Hi,
I am working on mesh hub. I am using the sample code Provisioner. I want to control the light node is a connect to the provisioner.
Any sample codes are available...
Hello,
I'm using the nRF52840 DK and I have a TensorFlow Lite model (.tflite) larger than 1 MB. Is it possible to load this model from external flash memory instead of internal...
Currently we are exploring the features of BLE mesh to integrate this in upcoming project. In this architecture, we plan to use 2 Provisioner in the mesh and one of the provisioner...
Hello,
I am using the nRF5340 in my project, and the device is capable of communicating with a mobile phone over BLE . However, we occasionally encounter a connection error...
Hello
I’m aware that this topic has been discussed in several posts from a couple of years ago, but I haven’t found a concrete solution yet.
I'm currently using an external...
