Dear Technical Support Team,
I am trying to integrate and run TensorFlow Lite Micro on the nRF5340 Development Kit using the nRF Connect SDK. I have tested both SDK version...
Hi,
I am working with the NRF52832 SoC using the NRF52 DK and developing with NRF Connect SDK version 2.7.0. I have enabled BLE with LBS, BAS, and FUOTA services, along...
It is nRF54L15 + SDK 3.0 + Matter application.
I have developed a custom BLE service that is based on Nordic's proprietary NUS BLE service. The BLE custom service is enabled...
I am testing out the nRF54H20 on the nRF54H20-DK version 0.9.1. I have followed the steps for setup in the "Getting started with the nRF54H20 DK". I currently have nrf54h20_soc_binaries_v0...
I am trying to get a WiFi project working using the nRF52840DK and nRF7002EK . I use a 3.3V power source that is supplying power to both nRF's in parallel. For the nRF7002EK...
Hi,
I'm developing firmware for the nRF52840 DK using nRF Connect SDK v2.9.2 , and I’m running into a problem that didn’t occur in v2.8.0 .
My project uses Zephyr and...
I am receiving an error when connecting to a custom board by running nrfjprog --reset, any similarly with any other commands that require connection.
I am connecting through...
Hi,
just for understanding what soft device do i have to use when i want to build an application wich use observer role and broadcaster role at same time?
Can i use S110...
In our application, we need to save a group of data objects,
how many data objects in a group is dynamic.
also each data object has different sizes,
a few bytes up to 100...
Hi,
I am using nrf51822 custom board.
I'm trying to make intterrupt when a pin is 0 (or 1) and do some calculations while it remains 0.
However I could not manage...
Hello,
I am trying to use SPI on a mbed nRF51822 and am following the documentation suggestion. We've deleted all code except the minimum to try and track down the problem...
Hi,
i want to build an applicaiton with gcc and eclipse setup and S130. I use OSX.
if i don't use the softdevice and run it with the blank linkerscript my blinky code...
Hello,
We are trying to update to Keil uvision 5.11 and unfortunately breaking our teeth on the pack Installer. The Nordic SDK 5.2.0 is installed on the machine but when...
Hi,
I have installed nRF Master Control Panel app on custom board running Android kitkat 4.4.2(ASOP).
But when I run MCP app it gives prompt that 'Device doesn't support...
Hi all,
I develop a central application, which manages multiple peripheral connections. The application often has to stop and start scanning again. In rare cases the function...
Hi,
I'm trying to get the bootloader from SDK v6 running with SoftDevice v7.
I managed to compile it under Eclipse (gcc). I've just removed buttons and LEDs from the code...
I would like someone from Nordic to confirm that the new softdevice release s110_nrf51822_7.0.0 is not suitable for the 128kb versions of the chip (in my case nRF51822 QFABB0...
Hi!
How is the functionality choosen, the nRF51822 has to offer?
Is the SoftDevice (e.g. SD120) an API in C where a specific functionality (e.g. central role listening to...
Is it possible to use nRF51822 Development Kit without nRFgo Starter Kit? What I need - is to be able to connect couple of LEDs and buttons, can this be achieved without buying...
Hello,
after successfully calling sd_softdevice_enable(), I call ble_cscs_init() and that function returns with error code 7, which means NRF_ERROR_INVALID_PARAM. I've tracked...