Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Post:
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the...
I use the security mechanism dtls based on udp communication. Can I implement it on nrf52833? How much flash and ram should be occupied at least? Is there a suggested value...
I am testing gnss without lte connectivity, which seems to work ok.
Except when I get "The modem has detected a reset loop. LTE network attach is now restricted for the...
Hi,
nRF5340 and SDK v3.0.0 I'm using.
Currently my nRF5340 based BLE device can be bonded with smartphone via passkey, after bond is done, the device stops advertising...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
Hello All,
We need to design a Remote Control based on NRF24LE1 working with mercury cell.
So they key factor is hardware & software optimisation for the lowest possible...
Is anyone aware of any of these on the market yet? I know of one, from Insight SIP, but am keen to hear about any others.
(This would save space on the PCB, simplify our...
Using twi_sw_master have discovered that the nrf51422 E00 draws 1.3mA in off mode.
When the twi device is removed from the bus, the nrf51422 draws under 5uA in off mode...
I want to merge soft device, application and boot loader in order to improve efficiency for factory. I searched relative topics in this forum and found something useful. At...
We have been unable to establish a link between a Garmin HR monitor over the air, we have established USB comms to a cell phone device. We took the transmission line directly...
i find one related question:
devzone.nordicsemi.com/.../
and this is refers to nrf8001,
so, i wonder if nRF51 could share both crystal with other MCU?
please help to...
Hello,
I am trying to test ble_app_uart example code and replicate similar behaviour.
I have disabled hwfc. But without hwfc, UART0_IRQHandler is not getting called...
Hi
I need to implement I2C slave side (up to 100kBit/s) on a nRF51822 chip. As far as i see the inegrated TWI peripherial only supportes the master side. Any ideas how...
I just received an nRF51822 eval/development board that has a sticker on it that says "PCA10004". I also just downloaded the latest SDK (nrf51_sdk_V6_1_0).
As far as I...
I received my nRF51822 development kit today and the PCA10000 dongle doesn't appear to be working. I installed all the drivers/software as per the user guide and when I plug...
Hi,
I'm using s110 v7.0.0 and sdk v6.1.0.
Which situations can produce disconnection error 0x3E ?
( BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED )
how to avoid this error ...
Hi All,
Are there any updated examples for nrf51822 for writing long charecteristics.
My Application has to receive more than 20 bytes at a time and send over uart.
...
I'm looking to add PWM functionality to my design to drive an LED. Examples exist for other devices, and those don't use the SoftDevice. Is there an example or some reference...
