We have previously used nRF52840 and for the latest iteration of our board design we are updating to use nRF54L15.
We are aware that for nRF52840 we could map any pin to...
Hi,
I faced with an initialization issue of combination two features: MCUMGR and UART_ASYNC_API. I get a crash right after the FW starts. It looks like the SW configuration...
I checked the nrf52832 manual and found that both XC1 and CX2 are analog input pins for the 32Mhz clock pin configuration. The reference design for both uses 32Mhz crystals...
Hello, I need to configure and compile a sample to send an audio stream (mp3) to the I2S interface.
I tried to put together some configuration from other samples but no...
hi support team,
when i testing wifi location, i found out one problem:
nrf_cloud_rest: Failed to encode location request, err: -12
that is this code in nrf_cloud_rest...
Hi,
I'm using the nRF52840 with the SoftDevice for BLE. In my system, it's primarily a BLE transceiver controlled via SPI by an external TI MSP430. We're considering implementing...
Hello,
I'm looking for guidance and understanding of how to properly use the KMU and ITS for secure key storage of a key generated on device.
I see that typical ITS use...
Hi dear friends from Nordic Semi,
I´m in great trouble trying to make these nRF24L01+ to work, one unit as a transmiter, and one unit as a receiver, it can be to send 3 bytes...
Hi,
I am using nRF51822 Evaluation Kit along with keil uvision4. Will using optimization in keil IDE make any problem in the normal working of BLE project? Will it affect...
Hello All,
We need to design a Remote Control based on NRF24LE1 working with mercury cell.
So they key factor is hardware & software optimisation for the lowest possible...
Is anyone aware of any of these on the market yet? I know of one, from Insight SIP, but am keen to hear about any others.
(This would save space on the PCB, simplify our...
Using twi_sw_master have discovered that the nrf51422 E00 draws 1.3mA in off mode.
When the twi device is removed from the bus, the nrf51422 draws under 5uA in off mode...
I want to merge soft device, application and boot loader in order to improve efficiency for factory. I searched relative topics in this forum and found something useful. At...
We have been unable to establish a link between a Garmin HR monitor over the air, we have established USB comms to a cell phone device. We took the transmission line directly...
i find one related question:
devzone.nordicsemi.com/.../
and this is refers to nrf8001,
so, i wonder if nRF51 could share both crystal with other MCU?
please help to...
Hello,
I am trying to test ble_app_uart example code and replicate similar behaviour.
I have disabled hwfc. But without hwfc, UART0_IRQHandler is not getting called...
Hi
I need to implement I2C slave side (up to 100kBit/s) on a nRF51822 chip. As far as i see the inegrated TWI peripherial only supportes the master side. Any ideas how...
I just received an nRF51822 eval/development board that has a sticker on it that says "PCA10004". I also just downloaded the latest SDK (nrf51_sdk_V6_1_0).
As far as I...
I received my nRF51822 development kit today and the PCA10000 dongle doesn't appear to be working. I installed all the drivers/software as per the user guide and when I plug...
Hi,
I'm using s110 v7.0.0 and sdk v6.1.0.
Which situations can produce disconnection error 0x3E ?
( BLE_HCI_CONN_FAILED_TO_BE_ESTABLISHED )
how to avoid this error ...
Hi All,
Are there any updated examples for nrf51822 for writing long charecteristics.
My Application has to receive more than 20 bytes at a time and send over uart.
...
