I am working on a project using a ble nano (nrf51822) using the Nordic SDK 8.1. In the examples I found a way to control an LED using the methods LEDS_ON and LEDS_OFF. I wanted...
Hello,
I am using ble_app_gls example and I have implemented static passkey in the code. Now I want to see if wireshark shows the passkey when I connect to ble devices. For...
Hi Team,
We are implementing an UART communication between a M4 processor (UART master) and a nRF51 (UART slave) and we want to use the UART in Low Power mode with flow...
Hello everybody,
for my project, i will bond the peripherial with the central.
I test my device with the MCP and can connect without problems. When i press the Bond Button...
Hi all,
I am trying to count the positive edges of a 3.5MHz signal with GPIOTE, PPI and the TIMER1. Unfortunately i can only measure to frequencies up to a little more...
Loaded Softdevice S140, ( Using NRF52840 DK board ) using NRFgo Studio.
App flash base is set to 0x00021000 and app RAM base is set to 0x20003000
Looking at the CPU...
In our earlier projects with nRF51 and SDK 8 we used to have bluetooth device names of length 13 or 14 characters. However, when using nRF52 and SDK 12 I noticed that the...
Hi All,
I am working a custom board for 51822. We have wired the UART RX/TX pins to a microusb connector (No RXD/TXD pins wired). The problem is once we connect it to PC...
Hello,
all was working fine, until today.
When I plug my dongle, my computer does not react.
The green light on the dongle is off.
Even if I suppose that it's a...
For my current project, I need to compile the »over the air bootloader« with gcc (because our buildserver runs on linux, developers using Mac … no Windows and no Keil so far...
Hello, I want to get Pwm output using softdevice but i am not getting it.Here is my code attached main.c please tell me where i am going wrong.Do ineed to initialize softdevice...
I am looking at using the nRF51822 in an application to create an Ethernet gateway and want to be able to download new firmware to the nRF51822 from a remote server. I plan...
I have an nRF51822 application using the Soft Device 110. I want to perform bonding with a central without MITM protection. In my on_ble_evt() event handler, when the event...
Hi,
I am new to the scene of BLE beacon development. I am using multiple Bluetooth smart beacon kits for indoor ranging/positioning purposes. To reduce the effect of interference...
Hi,
For S110 6.0.0 we use such script to split hex to binary. But it seems 7.0.0 is changed and current way is not working anymore.
Convert from hex to binary. Split...
Hi
I am writing my own bonding manager.
In the S110 stack after Phase 3 of pairing the keys are exchanged which result in the EVT_AUTH_STATUS event which in turn contains...
when I add my own service and add characteristic, a odd phenomenon confuse me.
When I set cccd_md.write_perm:
BLE_GAP_CONN_SEC_MODE_SET_OPEN(&cccd_md.write_perm);
...
after several attempts to debug and understand what goes in my handlers in the BLE callbacks, I thought to give a UART logger a try.
this is what I'm trying to use: OpenLog...
Hello,
I am looking for a not expensive way to program nRF51822 by frame of 10 modules. All the 10 modules would be connected to a PC using pogo pins, and I would use a...
I can get an information that bluetooth smart connects bluetooth smart ready.
But I can't get an information that bluetooth smart connect bluetooth smart ready.
So, Would...
I am using nrf51822 and i want to run my application using softdevice.
But I am not able to start my softdevice Please can anyone guide me how to start my softdevice.
I...
