I'd like to erase all the pages managed by FDS as part of a "Hard Reset" operation. fds.c has a hint of a "FRESH_INSTALL" directive (part of an enum defined in fds_internal_defs...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
Hello.
I would like to develop FW for the nRF52832, using Eclipse IDE + ARM GCC + Segger JLink OB.
I've seen on the segger webpage that the nRF52832 is a Cortex M4 processor...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
I need to be able to actively set the value being incremented in the Timer2 register on the nrf52 (what I believe would be it's main register). It seems that this might be...
The errata for the nRF52 indicates higher consumption in managing timers and GPIOTE. Does the BSP for SDK11 follow recommended practice to deal with these errata can I ask...
Hi,
I am trying to understand the pstorage to record a log for temperature. In my code, I can call pstorage_init(), and clear a block but when I try to store some data...
My device is smart watch. We transfer some data to phone and receive notification from phone over BLE.
My question is those two functions(connect_params_init and sec_params_init...
Hello
I'm new in the world of nordic semiconductor and I've a little problem. I would like to transfer ANT+ data of a HRM Garmin in serial protocol to my PC. I use a nRF51422...
Hi,
I transmit a data packet to AP2, i wonder if it needs a sequence for resetting or not while AP2
initializing.
And, I send a packet data to AP2 by UART(AP2...
Hi Folks,
I'm experiencing a problem with the nRF8001 setup. After I send the last setup packet, I still receive:
0x03 (length), 0x84(CommandResponseEvent), 0x06(Setup...
I'm getting this error, but oddly it's coming up somewhere in the MIDDLE of my build, and not always the same point.
I have modified the HEAP size to be 0 as I don't do...
Hello !
I have just received the Evaluation Kit nRF51822-EK. I succeed to compile link and load the blinking leds example from my Linux box. I modify the example to use...
So, how do I control where my app is going when gdb pushes it to the device?
I'm using s110 6.0.0, no boot loader. How do I make sure my app is going to where the SD will...
Hello,
I'm trying to make use of the AES crypt code from the application level code.
Per devzone.nordicsemi.com/.../51822-aes-encryption-and-decryption-demo-code
...
I am planning to record some information in the flash of the nRF51822. This will occupy a large circular buffer (quite a few kb), and new data (in chunks of around a dozen...
hi,
i survey the Bluetooth again , i have some issue about the Connectable mode
Connectable mode.
i see the peripheral connectable setting :
PERIPHERAL :
...
Hi Nordic,
How many connections was S120(Central) can handle simultaneously?
Does S120(Central) can received the notifications from different peripherals...
Dear all
I notice that Gzaell could only send 32 bytes a packet. But I check register PCNF1 MAXLEN can be set over than 32 bytes.
Is there any way to increase overall...
Hello,
Is there a way to set the OOB key while using the master control panel windows software?
Edit: and if not, is there a quick method to test a peripheral's OOB...
Hello!
1)There is problem with nrf_ble_uart. On sdk 4.4 work well, but sdk 5.1 the same code is not working.
What changes were made in the sdk or maybe there is a ready...
