Hi,
The situation:
I was able to successfully receive known packets from a device running gzp_device_dynamic_pairing, from, the host running the gzp_host_dynamic_pairing...
Hi everyone
nrf51822,softdevice s130 2.0.0
now i used softdevice s130 establish two connection as a central with two s110 peripheral device,at the same time i establish...
Hello , I want use nrf24lu as "Hos" and nrf51822 as 'Device'.
I need some info about nrf24xx whith gazell .but I can't find info bout those param like:
typedef enum...
When you download win driver (from www.nordicsemi.com/.../72324929 for instance). There's only a win32 dll/lib provided.
However, modern development are often made on 64bits...
hello, Nrf24LU (Rx) , nRF51822(Tx).
The Nrf24LU Can only receive one packet。
if I use this function twice ， like this：
The Nrf24LU can receive Continuous.
I guess The...
Hi,
I use SDK v10, S110 v8 and dfu_dual_bank_ble_s100_pca10028. My application has dfu support.
I reset to bootloader from application after writing 0x0104 to dfu control...
Hello,
I'm using GCC with the soft device 6.0.0. I'm having this reoccurring issue where sometimes I will start to debug and the execution flow will get stuck in some kind...
Hi,
I catched the air data packets by Sniffer and it shown that there was an error, MIC incorrect, which could be seen as followed, and the whole packet was malformed....
Hi!
I have some problem to reconnect an already bonded device containing a chip nRF8001 rev D with my iOS app. Rev C works fine with the first connection and the reconnection...
HI,
I want use some GPIO to detect "pin_high_to_low" or " pin_low_to_high".
and I think the "app_gpiote.c" might be helpful.
but I have been confused by function " sense_level_toggle...
Hi,
I'm starting to implement DFU using IAR's ARM workbench. In the example project for ARM that comes with the nrf51_sdk_v5_2_0_39364 SDK there is a file called bootloader_util_arm...
Do I have to use external host MCU for nRF51422? What can the ARM Cortex processor inside SoC 51422 do and cannot do?
I want to create a mesh network with hundreds of ANT...
I want to load a Blinky project to the AK board, and the dongle is used as a jlink, but I forget to move the jumper to the 'out', and the program is loaded to the dongle....
Hi,
I change the example ant_broadcast to acknowledge mode, but it seems that without a peripheral side,the LED0 will still twinkle.I don't know how to change the project...
Hi,
I'm porting a nrf51822 evaluation board 10001 tested application to a custom board. Part of the application is using UART interrupts to raise a flag and start data...
I am experiencing an error in the final linking stage of my build.
_build/blinky_gcc_xxaa_s120_xxaa.bin: file not recognized: File format not recognized
collect2.exe...
Hi
I am looking at section 9.1 of the S110 Softdevice Specification v1.3A and the release notes for 7.0.0-2.alpha where I see that an application now starts at 0x15000...
Hi
S110 v7.0.0-2.alpha got released today.
In the release notes it says...
[b]The SoftDevice can now be configured to forward interrupts to one of several applications...
My application seems to be running out of memory, now I received NRF_ERROR_NO_MEM from sd_ble_gap_ppcsp_set. I don't understand why this has started since I don't think i...
Im using custom board with nRF8001. I'm using Hello World example from GitHub.
The nrf chip revision is C not D. When I connect the board to Arduino Leonardo the device start...
