I read this older post ( devzone.nordicsemi.com/.../) and have a similar issue but with enough differences that I felt it was worth a new question.
I have an STM32 MCU...
I am having an issue with running the initial blinky example that came with the nRF51 PCA10028 SDK in the Eclipse IDE . I will include screenshots of the issue. I believe...
I use nRF51-DK and nRF51-Dongle for a BLE sniffer.
Always the sniffer fails and marked with an error "Encrypted packet decrypted incorrectly (bad MIC)".
It can not be...
Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
It might be due to a short circuit caused by incorrect wiring. The PPK2 circuit board is damaged, and the chip with silkscreen "L7 #247" in the lower-right corner seems to...
Hello,
we have a working system on the nrf9161 that works without zephyr. We have our own secure firmware that successfully uses the cc310 after we start the actual application...
Hello DevZone,
Is it possible to support Matter over Ethernet and Matter over Wi-Fi at same time?
Since there are many Ethernet chips support in Zephyr.
Seems that the...
When my mtd device is connected to a thread network, what should I do if I want to untie and join another thread network? How should I untie and clear the network information...
Hi,
I'm looking to continuously sample the ADC at a high sample rate with rotating buffers.
I found an example code that matches what I need with the older SDK for...
Hello. Right now, I am connecting an external flash using SPI. The external flash is used for firmware updates. I'm trying to launch sQSPI to access the external flash. I...
We are using nRF5340 with nRF7002 on our custom board. Our application requires:
Wi-Fi (via nRF7002)
Thread (via nRF5340)
DFU over Wi-Fi
We are concerned...
Testing with NCS 3.0.1 and nRF54L15-DK. I would like my devices to be able to work as channel sounding initiator as well as reflector role. In my own code I have integrated...
I have this main code:
With this overlay:
and this configuration:
I am using a nrf52840 dev board and have connected P0.06 and P0.08.
Why does it not trigger...
SOC: nrf52840
SDK: v2.9.0
Device is a central, it connected to 16 peripherals, these peripherals will power on 90 seconds and then power off 10 seconds(one cycle). ...
We have peripheral, and we want to connect it using NRF 52840. when we are bonding this using nrf connect app we get a pop up with random key and using pair we can pair with...
I'm using the nRF9160 with the LIS2DH accelerometer and SDK version 2.5.2 . In my hardware setup, INT1 is connected to GPIO 0 and INT2 to GPIO 1 . I'm configuring both interrupt...
Hello,
I am currently using the `AT%XICCID` to obtain the ICCID of Hologram eSIMs. The output of some of these eSIMs are just the raw 20 digit ICCID with no ending checksum...
Hi,
I’m looking for your recommendations on a suitable conformal coating for an application subject to high humidity. The goal is to mitigate any potential risk of short...
Hi I am trying to get an SD card hooked up to my nrf52840 devkit. I am using nRF Connect v2.6.1 and I was trying to get the sample code working, so I used the sample in ncs...
