When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I have Olimex Mod-nRF 8001 Module which i bought it from here . It has break out the RDYN,REQN,MISO,MOSI,SCK and reset pins. My question is can i connect RDYN and REQN lines...
I used the Nexus 5 with android OS 4.4 and try to
use both the "Master control panel" and "Toolbox" Apps to upload firmware.(DFU)
When I use the "Master control panel" App...
We are using an nRF51822 with s110 v5 and an iPhone. When the iPhone connects to the nRF51822, occasionally (perhaps 1/4 of the time) the iPhone fails to complete service...
Having some issues with the examples on the nRF51822 development kit. Hoping someone can help.
Working from nRF51822_Development_Kit_User_Guide_v1.3.pdf.
Motherboard...
Hi all.
I am making a PCB for nRF51822. My PCB need is to talk with iPhone for BLE Proximity application. Also I need to control a LED from iPhone. And I need to get low...
In short: Is it feasible to use RSSI values when tuning the antenna?
I have a custom board with an nRF51422 on which I have designed the RF part to be as much as possibly...
Any suggestions for handling a bricked custom board?
I'm pretty sure I know where the problem is in my code, but now I can't reprogram the board. I did have this happen...
Hi, I'm developing an BLE application using nrf51822.
I have a BLE security issue to discuss.
(Actually I don't have much network security background...)
In our application...
I'm using PCA100001 board with pure-gcc Makefile and s110_nrf51822_5.2.1_softdevice.
And I'm writing simple code customizing s110 samples like below:
static void ble_stack_init...
Hi
Does the NRF51822 support ANT and where would be a good place to understand how to implement ANT ? I also want to know where I can get more information regarding the...
Hello community, first time posting a question so please try and forgive any future mistakes.
anyways im new to using the keil IDE and am have some problems. I have dug...
I am using pca10001 board and started my development from nrf6310/s110/ble_app_hids_keyboard.
SDK version is 6.0.0. I have successfully tested my device with (MCP) Master...
Hi,
I am very new to BlueTooth technology. Currently i'm testing the nRF51822 evaluation kit to see if the BLE module can be used for a specific project. I've tried several...
I have a schematic in which Balun is connected as a matching network to Ant1&Ant2 pins making the output impedance 50 ohms. Now i want to connect an Antennae to it which is...
Pages 51 and 53 of the nRF8001 Product Specification (v1.2) show a reference design for a balun network in which capacitor C4 is listed with a value of "N/C". The component...
