I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Please tell me the Manufacture Part no: which is used for the 16MHz crystal in the PCA10040 DK. I found it different from the one used in PCA10028 version of the DK with just...
Please tell me the location to download the hardware files for pca10040 version of the nRF51 DK board. I could find only pca10028's hardware files in the nordic's webpage...
Hi,
I have some similar problem when trying to add the custom 128bit characteristic UUID.
The service UUID is advertised correctly but the characteristic UUID not.
...
Im using nrf51822 (16KB RAM), I'm trying to retain some data (RAM) after watchdog reset. when I load only the softdevice and my app, the RAM retention workings, but when I...
HI , ALL
i coded the uart_init in my project.
and i want to regarget the printf in my project.
so i find the retarget function is in the 'retarget.c' ,
i tried...
Hi,
We are using Softdevice S310 Version:3.0.0 and SDK:9.0.0.
My Device working on battery power. We are facing Flash write problem when my battery voltage goes to below...
Please tell me the safe 'Max Voltage Rating' for the capacitor at the DCC pin of the nrf51822 in DCDC mode. I am talking about the C12 cap in the circuit shown in Page 113...
Hi all,
I have an interesting problem where I want to read my bootloaders version (based on the DFU), which I have located at 0x3C100, from my application.
I confirmed...
HI , ALL
in the PS document, i know that there a register for the interruption --- INTENSET.
i wanna know if there is an api to set the interrupt.（or the only is to...
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
I want to set its registers by uart I/F.
Because our host cpu(ARM9) has no SWD I/F.
How can I set its registers by using uart I/F?
I read a document of "nRF51_Series_Reference_manual...
Hi,
Please help me...
This is the first We are launching our product which uses nRF51822 SOC, But I have no idea how do i write manufacturing test? or what are the tests...
Hello,
What I need to do is control a small 128x64px SSD1306 display with my beacon. Could anyone please give me some directions to follow? I tried this library but had...
