The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
I use an app_timer to gather ADCs and send with Gazell with period 5ms.
What I suffered is the sent packet is different from what I put in buffer.
my pseudo code...
I am able to send data from EK to MCP but even i am sending one byte of ASCII(alphabet) of data, it is showing as hex value in MCP ex., 'C' as 43 , if i want to see ASCII...
Hi,
How to set the advertisement parameter's (uuid's list) , while using both custom and SIG adopted services?
I modified the source code as below, but it is not showing...
I would like to implement a simple wireless sensor network, using Enhanced Shockburst with Auto-ACK. The idea is that there will be many sensor nodes (SNs) reporting to one...
I have a question about using the GPIOs,I found that I can set a ‘1’ at the same bit position of OUTSET register and OUTCLR register. But which one is effective ?
Hello guys,
Looking through the product specification for nRF8001 I am still not clear on whether a master device can be connected to the nRF8001 (in peripheral mode) and...
Hi,
When erasing one page flash for responding one GATT request, it always went into assert_nrf_callback and has to reset the app. So I have to disable SoftDevice before...
Hello,
I am going to start programming BLE application, and I would like to know which enviroment is best to program it. Are there too many differences between programming...
Hello
According to the documentation the optimal CPU frequency is 16 MHz, Please, could someone tell me if that is correct or not?
Thanks for your help
Hi,
I modified the ble_app_hrs sample application with one custom service which includes, some custom characteristics (128 bit uuid), Now the problem i am facing is, i am...
Hi,
How to implement the passkey authentication, we are using nF51822 evaluation board. Is it possible to display the passkey using master control panel? And, we also don...
Howdy,
In a similar vein to my recent question about production programming....and nothing to do with takign an nRF51822 out for a walk :)
We'll write a simple test...
Hi
Before, TX and RX functions run well at iOS6. After we updated to iOS7, RX still worked but TX couldn't send out data. Did you verify nRF UART app at iOS7?
I'm reseaching a tag in low energy-cost using the nRF24le1.Till now,I can receive the message from the tag successfully, but can't send the command to the tag to read or write...
