Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
We would like to be able to calibrate the rRF9E5 ADC
Our proposal is to permanently fit voltage dividers, each using two precision resistors, on two of the ADC Ports and...
At some point in the past I had nrf51+gdb+breakpoints working just fine. I even have a bunch of __BKPT() calls in my various error handlers to trap into the debugger.
At...
Hi,
I'm trying to program nRF51822 Beacon Kit using nRF51DK. I'm trying to load the example ble_app_beacon to the beacon kit. After uploading SoftDevice 7.1.0, I try to...
Hello
I'm using the nRF51 DK and I have a UART over BLE link set up between the board and a phone with the nRF UART app. I'm trying to get the board to execute a particular...
I'm running into a weird problem where there is a long delay that is variable between calling ble_conn_params_change_conn_params() and receiving the BLE_GAP_EVT_CONN_PARAM_UPDATE...
Hello,
I've got a problem with my nRF51 DK. When I attach it to the USB port the drive doesn't appear on Windows explorer and green diode doesn't flash too.
I've been...
By design, the TI LP55231 LED driver IC will fail the TWI write of the reset register (0x3D). It's necessary to reset the IC in an edge use case. I'm using the nRF51822 HW...
Hi,
I want to write a characteristic, the value size is fixed, for example the size is 4 bytes. When I try to wirte 6 bytes from the client, the first 4 bytes is writed succesfully...
Hi all,
I have the nRF52 DK programming consistently without any trouble both on Kiel and using the nRFgo Studio.
My problems arise when I connect a 3rd party module...
Hi,
im trying to set up 3 PWMs for simulating a RGB LED with the 3 leds on the nrf52-dk.
I need the following behavior:
pushing on a button increases the width of the...
Hi,
I have implemented a custom application(Lets name that file app.hex) which works and sends the data to phone via BLE on my nrf51822 DK. I am using the s110 v8 softdevice...
Due to some constraints in the manufacturing process of my product, there is substantial mechanical variation in the BLE antenna. I can constrain this variation to a degree...
Hi,
I am trying to program MDBT40 with Jlink and having some problems.
Here is the scenario:
I have two versions of the MDBT40. One that I took off a BLE NANO (RedBear...
Hi,
I tried to get the sample ble_app_uart to work on NRF51422_DK with the S130.2.0.0 soft_device.
The compilation and programmation of the board is OK.
The soft run...
Hi all, i recently posted some topics about my application to receive support, everything went good but now i need to add a last step to the project, and i would like to have...
I am using nordic_sdk_10 for PCA10001. what are the BSP changes and config changes needed after replicating PCA10028 for DFU over UART.
I just changed CFLAFS & ASM FLAGS...
Hi,
I am storing data using pstorage module but when i power off my nrf51-dk board, the contents get deleted and not retained in memory. What could be the reason for that...
