I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi all,
I'm having a error on my code, and wanted to understand it better. I'm using a custom board with a Rev.3 CTAA chip, 256k Flash and 16k Ram. I have BLE initialized...
I measured my Nrf51822 current:
when my VCC is 3.0v ~ 3.3v
my current is 0.16 mA.
when my VCC is 2.6v ~ 2.8v
my current is 1.5 mA (why?)
when my VCC is lower than 2...
I have issue with nrf51 booting, i noticed that sometimes when i plug the power to (VDD and GND) the system dosent turn on at al.
1 - how does the system the whole system...
amigos de habla hispana estoy comenzando con este circuito.
mi duda es cual compilador utilizo para crear un simple led blink..
tienen algun tutorial en que me puedan a...
Hi.
I am using the nRF52 Preview Dev. Kit to send data over multiple channels by
setting the NRF_RADIO->FREQUENCY register to the desired frequency value.
To make it work...
Hi,
I am trying to measure the temperature using sht21 sensor with nrf51822. I am using TWI to do this. When I try to send a data to the sensor the application cannot do...
Using the nRF52832 and SoftDevice s132.
If the application code disables the SoftDevice, then the application CAN erase UICR memory in the nRF52832 device.
The question...
I control a module over UART using app_uart_fifo. This module is controlled from nRF host by commands to perform things. This generally works fine but however, sometimes when...
Hi,
I write a code for the max6657 temperture via modifying the SPI MASTER Example. The function for reading max6675 via SPI is shown as follow
uint16_t readCelsius(void...
Dear Nordic Team,
Thanks for supporting.
How to calculate the battery voltage level from Eddystone TLM. Its always transmit 240mV.
I am using CR2302 3V battery.
...
Hi all !
Can you tell me if it is possible to flash a single nrf51822 ship directly or if it requires at least the minimum oscillator X1 in order to be flashed?
The...
Hello. I want only 1 to 1 bluetooth matching about nrf51822.
I want only 1EA central with 1EA peripheral matching.
I set as below.
1EA - Bluetooth Central - UUID...
Yesterday, I asked a question (so far, no one has answered) about how an OS upgrade on my desktop computer might have broken my ability to flash and run BLE apps on the nRF52...
Hi there,
I have two nRF52 Preview DK boards, SDK 0.9.1 and 0.9.2, and SoftDevice S132 1.0.0-3 alpha. Several months back I got the Bluetooth heart rate demo from SDK 0...
