Hi,
how long does it take time if i would wake up a nrf51422 rev2 (ANT and BLE) in deepest possible sleep mode ?
And how long does it tai if after wakeup it had to communicate...
I saw that the app_timer uses the SWI0. Could you explain what it does and what the advantage is compared to "timer_list_handler_sched()" calling "timer_list_handler()" directly...
Hi, I used the sample code "Master Emulator->2.1.7.8226->Example code->nRFUart"
to develop a new project, and encounter some questions...
we update nRF6310...
Hello,
How many RX buffers are in S110 SoftDevice? I know there are 6 TX buffers (so you can send 6 packets per Connection Interval).
How is it on receiving?
Is it e...
My sensor is off-standard,so I have to use gpio to read and write my sensor.
Gpio IIC will take about 0.5ms to get data.
My app need send data every 7.5ms,it seems that...
Hi,
My android Proximity application fails on service discovery only for the very first time it connects with the devices(nrf51822 evaluation kit with sdk 5.2.0). Actually...
Has anyone converted the app note AN34 DTM Python script to C# or C/C++ ?
The Python DTM script is works OK with the setup specified in the app note AN34 figure 2, which...
Hi,
I there a way that I can detect if a sections of my code has been interrupted by the Softdevice? I have some time critical code (bit banging a communication protocol...
Hi All,
I am using the nrf51422 and softdevice S310 to send out ANT+ and BT Smart in my project.
I use RTC1->Counter in order to get a timestamp for an interrupt from...
Currently we are considering whether we should use external Flash Memory or NRF52 Internal Flash.
External Flash memory has a lot of drawback in comparsion with internal...
Hi,
I am trying to run an example project which includes a softdevice using Keil uVision on nrf51822xxAA. What should I change in Options for Target? Especially what should...
Hi,
If I connect a peripheral and establish a bonding with MITM the connection security changes to mode 1 / level 3. If the peripheral is disconnected and reconnected the...
Hi,
I am trying to write program follow this structure: first I will enable button using GPIO, then wait botton is pressed, then I read ADC from GPIO pin, if ADC value >...
I'm using a nRF51 beacon as a receiver that produces a pulse when it receives a byte from the transmitter. The code is based on the ble_app_uart example. And I set the connection...
The new v3 of sd132 now has 4 characteristics in the GAP service.
The new one has uuid 2AA6
For some legacy testing I need to disable it's inclusion.
I have searched the...
Hi
I'm using the connectivity interface of the softdevices a lot and recently failures in the documentation of the connectivity protocol caused a long debug session. Maybe...
Hello,
I want to use the NUS service on my BLE communication. I don't have pins connected for UART, do I need to have them?
When I try to run the device, my program initializes...
hi,
1/ i notice that drivers header files are available in two versions. one inside "components\drivers_nrf" folder and the other inside "components\libraries".
and...
I'm using the nRF51822 DK + SDK10.0.0 + s110. I modified the app_ble_hrs example to send 2x 20B packets of data (via a modified heart_rate_meas_send() function) upon a m_battery_timer_id...
Hi
I have a custom board with no external crystal. Using S130 works fine, but I want to enhance communication with some data being sent over ESB using timeslot API.
...
My English is still poor, but I hope you can understand me.
Press the button to call ble_advertising_start(), which may occasionally restart main.
I set a short timeout...
I am using the FreeRTOS port included in a nRF52832 with nRF5 v11.0.0 + s132. From main() I create a task and I pass it some input data as argument. That data is encapsulated...
